CT2565-001-1 AEROFLEX [Aeroflex Circuit Technology], CT2565-001-1 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
CT2565-001-1
Manufacturer Part Number
CT2565-001-1
Description
CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B
Manufacturer
AEROFLEX [Aeroflex Circuit Technology]
Datasheet
1.CT2565-001-1.pdf
(31 pages)
Aeroflex Circuit Technology
A command word transfer will be initiated by the
CT2565 after the rising edge of NBGRNT (See
Figure 14). In order to allow the command word to be
stored in user-defined memory space (separate from
data), no memory write operation (CS, WR, ADRINC
outputs) will be initiated following the usual DMA-type
handshake; a Start Of Message (pin 78: SOM low)
pulse indicates that the CMD word is currently valid on
the data bus. Note that commands are named from
the BC point-of-view (i.e., a TRANSMIT CMD dictates
that the addressed RTU must transmit data).
If the subsystem is available (pin 47: SSBUSY high):
following transmission of the status word, the CT2565
will initiate a handshake/memory-read respectively for
the total number of (data) words defined by the
Command Word-word count field.
the RTU Read/Write Timing. Note that possible data
word transfer and short-loop test errors will be
reflected in the following status word/bit word. A low
on the SSBUSY input will set the corresponding status
word flag, and no data transfer will be requested
(BUSREQ low) following transmission of the status
word.
Receive CMD (BC-RT). A DMA handshake will be
initiated for each word received over the 1553 data bus
(See Figure 16).
handshake will be followed by a corresponding
memory write.
timeout or SS BUSY will not terminate transfer
attempts for the remaining data words, error flagging
or status word transmission.
RTU(b)-RTU(a)
RTU Commands
Transmit CMD (RT-BC)
Notes:
(1) The HSFAIL low output is reset (high) at the start of the next message transfer (NBGRNT low).
(2) The subsystem can use the status input pins (SW) to report incorrect word count type errors.
(3) MSGERR set 7.5µS after last mid parity bit of last data word.
COMMAND WORD
DATA WORD
LOOP WORD
TRANSFER/CONDITION
Invalid Word Format
Invalid Command (format error)
Handshake Failure
Illegal Mode Command
RT-RT Transfer
Handshake Failure
Number Transmitted
Short Loop
Long Loop
Response Timeout
Address mismatch
Transmit Command
Receive Command
Transfer errors such as handshake
(Transmit/Receive).
(2)
If successful, the respective
Sync, bit count invalid.
Operation disagreement (e.g. Broadcast and
BUSREQ to BUSGRNT timeout
Subsystem set ILLCMD (pin 48).
(Transmit) Command to Status Word time.
Transmit Command Address
BUSREQ to BUSGRNT timeout
(Continue)
(Message terminated)
Low data word-count received.
High data word count
Looped back through receiver.
Received word
(BC only)
DESCRIPTION
Transmit bits set)
address.
Figure 15 shows
Table 6 – RTU Error Handling
An
RT-RT
to last xmitted 1553 word.
14
transfer will appear to both RTU subsystems as a
standard transmit or receive command except:
transmission of the data block will not be continuous
with that of the receive CMD, and, (2) upon detection
of a command-sync field following the receive CMD,
RTU(a) will recognize an RT-RT transfer and store the
transmit CMD-address field for comparison with the
address field of the following (RTU(b) status) word
(See Figures 17 and 18). If a mismatch is detected,
RTU(a) will issue a message error. The transmitting
RTU will respond as in an RT-BC Transmit CMD.
Message transfer errors are indicated using the
TIMEOUT,
RTU-status outputs (pins 4, 5, 30 and 46 respectively).
Additional error detection mechanisms available
include
evaluation of the status and BIT words (See BIT
Word).
Table 6 describes error handling mechanisms related
to each stage in a message transfer (reading left to
right) as well as noting errors associated with a
specific CT2565 status output (reading right to left).
Short Loop Test. The last word to be transmitted in a
given message transfer (Status word, BIT word or
Data word) is stored in a CT2565 internal register. As
this word is transmitted to the 1553 bus, it is "looped
back" through the active receiver channel for
auto-RTU, "SHORTLOOP" verification. A LOOPERR
low pulse indicates a mismatch between the stored
and looped words.
initiated for all RTU transfers except a Broadcast
transfer.
RTU Status/Error Handling
Status Word
status
HSFAIL,
input
SCDCT2565 REV B 8/10/99 Plainview NY (516) 694-6700
Note that short loop testing is
None; input ignored
MSGERR (also; SW bit)
HSFAIL, suppress
SOM, continue
SW message error bit set
TIMEOUT (transmitting RT)
(also; MSGERR bit)
MSGERR (Receiving RT)
(also; MSGERR bit)
HSFAIL
Continue message transfer
INCMD high, EOM
MSGERR
MSGERR after validation
(no transfer) SW and BIT-
Word also set.
LOOPER (also sets Ter-
Flag bit).
MSGERR
ERROR SIGNAL
manipulation
(1)
(3)
(SW bit)
and
(below)
LOOPERR
PIN
-
30
5
78
4
30
5
9,57
30
30
46
and
(1)