VCC6-QAA-100M00 ETC1 [List of Unclassifed Manufacturers], VCC6-QAA-100M00 Datasheet
VCC6-QAA-100M00
Related parts for VCC6-QAA-100M00
VCC6-QAA-100M00 Summary of contents
Page 1
... Storage Area Network Digital Video Broadband Access OUT Description OUT Vectron’s VCC6 Crystal Oscillator (XO) is quartz stabilized square wave generator with a LV-PECL output, operating off a 3.3 volt supply. The VCC6 uses 3 frequencies under 200MHz, resulting in low jitter performance, typically 0.3pS rms in the 12 kHz to 20MHz band ...
Page 2
... Includes calibration tolerance, operating temperature, supply voltage variations, aging (40 degreesC/10 years) and shock and vibration (not under operation). 5. Measurements made on a VCC6-QAB-155M520 using an Agilent E5052A for phase noise and LeCroy 8600, 25K samples for jitter. 6. Output will be enabled if Enable/Disable is left open. The pull resistor changes to a higher value, operating in a “power saving mode” when Enable/Disable is set to a logic 0 ...
Page 3
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Outline Diagram and Pin Out Table 2. VCC6-QAx Pinout Pin # Symbol E/D 3 GND Figure 3 Optional VCC6-QAx Package Drawing Table 3. VCC6-QCx Pinout Pin # Symbol 1 E GND Figure 4. VCC6-QCx and VCC6-QAx Package Drawing ...
Page 4
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Terminating PECL Outputs The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 5. There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6, and a pull-up/pull-down scheme as shown in Figure 7 ...
Page 5
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Enable/Disable Functional Description Under normal operation the Enable/Disable is left open, or set to a logic high state, and the VCC6 is in oscillation mode and outputs are enabled (active). When the E/D is set to a logic low, the oscillator stops and the both the output and complementary outputs are in a high impedance state ...
Page 6
... The VCC6 has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements and maximum parameters are listed in Table 6, lower temperatures are also acceptable. The VCC6 is hermetically sealed so an aqueous wash is not an issue. Frequencies >200MHz will need to be reflowed at 220C max. ...
Page 7
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Tape and Reel Table 8. Tape and Reel Dimensions (mm) Tape Dimensions Product VCC6 16 7.5 1.5 Vectron International 267 Lowell Rd, Hudson NH 03051 Figure 10. Tape and Reel Diagram Reel Dimensions Tel: 1-88-VECTRON-1 ...
Page 8
... C: E Pin 1, Pin NOTE: Not all combinations of options are available. A ±20ppm option over -10/70°C 3.3V, VCC6-107-frequency, is also available A ±20ppm option over -10/70°C 2.5V, VCC6-110-frequency, is also available. www.vectron.com Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application ...