ACS108-6SN STMICROELECTRONICS [STMicroelectronics], ACS108-6SN Datasheet
ACS108-6SN
Available stocks
Related parts for ACS108-6SN
ACS108-6SN Summary of contents
Page 1
... OUT ACS1086S ACS1086S G TM: ACS is a trademark of STMicroelectronics Rev 2 ACS108-6S AC switch family G COM OUT G OUT TO-92 SOT-223 ACS108-6SA ACS108-6SN OUT G COM Common drive reference to connect to the mains Output to connect to the load. Gate input to connect to the controller through gate resistor www.st.com COM 1/11 ...
Page 2
... T = 125 °C 0.1 j -40 to +150 -30 to +125 Quadrant Value II - III MAX III MAX III MIN 0.15 MAX 25 MAX 30 MIN 500 = 125 °C MIN 0.3 j MIN 650 ACS108-6S Unit A/µ °C Unit V/µs A/ms V ...
Page 3
... Characteristics Value MAX 1.3 MAX 0.90 MAX 300 2 MAX 0.2 Value TO-92 60 SOT-223 25 TO-92 150 SOT-223 60 RMS on-state current vs ambient temperature (full cycle) (A) ACS108-6SN (with 5cm² copper surface under tab) ACS108-6SA T °C amb 100 Unit V V mΩ µA mA Unit °C/W 125 3/11 ...
Page 4
... Figure 6. 1.E+03 t=20ms 1.E+02 One cycle 1.E+01 1.E+00 1.E-01 Number of cycles 100 1000 0.01 ACS108-6S Relative variation of gate trigger current, holding current and latching current vs junction temperature & (° 100 110 120 130 Non repetitive surge peak on-state current for a sinusoidal pulse with width tp< ...
Page 5
... ACS108-6S Figure 7. On-state characteristics (maximal values) 10.00 T max 0 300 mΩ d 1.00 Tj=125°C Tj=25°C 0.10 V (V) TM 0.01 0.0 0.5 1.0 1.5 2.0 Figure 9. Relative variation of critical rate of decrease of main current (di/dt)c versus junction temperature (dI/dt (dI/dt) [T =125 ° (° ...
Page 6
... AC line switch - basic application 2 AC line switch - basic application The ACS108-6S switch is triggered by a negative gate current flowing from the gate pin G. The switch can be driven directly by the digital controller through a resistor as shown in Figure 13. Thanks to its overvoltage protection and turn-off commutation performance, the ACS108-6S switch can drive a small power high inductive load with neither varistor nor additional turn-off snubber ...
Page 7
... AC line transient voltage ruggedness The ACS108-6S switch is able to withstand safely the AC line transients either by clamping the low energy spikes or by breaking over under high energy shocks, even with high turn-on current rises. The test circuit shown in is also used to test the ACS switch according to the IEC 61000-4-5 standard conditions. ...
Page 8
... Voltage 6 = 600 V Sensitivity Package A = TO- SOT-223 Packing TR = Tape and reel AP = Ammopack (TO-92) Blank = (TO-92) Bulk (SOT-223) Tube -TR Dimensions Ref Millimeters Min. Typ. Max. Min. A 1.35 B 4.70 C 2.54 D 4.40 0.173 E 12.70 0.500 F 3.70 a 0.50 ACS108-6S Inches Typ. Max. 0.053 0.185 0.100 0.146 0.019 ...
Page 9
... ACS108-6S Table 6. SOT-223 Mechanical data Figure 18. SOT-223 Footprint In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97 ...
Page 10
... Ordering information 5 Ordering information Part number ACS108-6SA ACS108-6SA-TR ACS108-6SA-AP ACS108-6SN-TR 6 Revision history Date 05-Jan-2005 07-Jun-2006 10/11 Marking Package ACS1086S TO-92 ACS1086S TO-92 ACS1086S TO-92 ACS1086S SOT-223 Revision 1 Initial release. 2 Reformatted to current standard. Replaced Figure 9. ACS108-6S Weight Base Qty Packing mode 0.2 g 2500 Bulk 0.2 g 2000 Tape and Reel ...
Page 11
... ACS108-6S Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any All ST products are sold pursuant to ST’s terms and conditions of sale. ...