TS1101 TOUCHSTONE [Touchstone Semiconductor Inc], TS1101 Datasheet
TS1101
Available stocks
Related parts for TS1101
TS1101 Summary of contents
Page 1
... TS1101’s RS+ and RS- input terminals. The SOT23 package makes the TS1101 an ideal choice for pcb-area-critical, supply-current-conscious, high-accuracy current-sense battery-powered and portable instruments. All TS1101s are specified for operation over the -40°C to +105°C extended temperature range. SIGN Comparator’s Symmetric I PA`RT TS1101-25 TS1101-50 ...
Page 2
... Soldering Temperature (Reflow) ............................ +260°C PART MARKING CARRIER QUANTITY Tape & Reel TADN Tape & Reel Tape & Reel TADP Tape & Reel Tape & Reel TADQ Tape & Reel Tape & Reel TADR Tape & Reel ----- 3000 ----- 3000 ----- 3000 ----- 3000 TS1101DS r1p0 RTFDS ...
Page 3
... SENSE For GAIN = 50, the applied V SENSE For GAIN = 100, the applied V For GAIN = 200, the applied V Note 6: The device is stable for any capacitive load at V Note the voltage from RS- TS1101DS r1p0 = 47nF 1.8V; T OUT DD A CONDITIONS T = +25° +25° ...
Page 4
... Input Offset Voltage vs Common-Mode Voltage 110 85 1 0.8 0.6 0.4 0 110 Gain Error Histogram -0.6 -0.2 0 0.4 0.6 -0.4 0.2 GAIN ERROR - % SUPPLY VOLTAGE - Volt Supply Current vs Common-Mode Voltage SUPPLY VOLTAGE - Volt TS1101DS r1p0 30 30 RTFDS ...
Page 5
... G = 100 3 2 1 100 SENSE Small-Signal Gain vs Frequency 100 - -15 -20 -25 -30 -35 0.001 0.01 0 FREQUENCY - kHz TS1101DS r1p0 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 150 0 - -40 -60 -80 -100 -120 -140 100 1000 0.001 TS1101 Gain Error vs. Temperature ...
Page 6
... Small-Signal Pulse Response, Gain = 25 200µs/DIV Small-Signal Pulse Response, Gain = 100 200µs/DIV Page 6 Large-Signal Pulse Response, Gain = 50 200µs/DIV Large-Signal Pulse Response, Gain = 25 200µs/DIV Large-Signal Pulse Response, Gain = 100 200µs/DIV TS1101DS r1p0 RTFDS ...
Page 7
... OUT SENSE RS+ resistor that is used to measure current. At the non- inverting input of the TS1101 (the RS- terminal), the applied voltage is I terminal is the non-inverting input of the internal op amp, op amp feedback action forces the inverting input of the internal op amp to the same potential (I x RSENSE) ...
Page 8
... DS M1 RGAINA LOAD RGAINA Since M1’s drain terminal is connected to ROUT, the output voltage of the TS1101 at the OUT terminal is, therefore LOAD S NS When the voltage at the RS- terminal is greater than the voltage at the RS+ terminal, the external VSENSE voltage drop is impressed upon RGAINB ...
Page 9
... Swing vs. Applied Input Voltage at V OUT and Desired V SENSE As there is no separate power supply pin for the TS1101, the circuit draws its power from the voltage at its RS+ and RS- terminals. Therefore, the signal voltage at the OUT terminal is bounded by the minimum voltage applied at the RS+ terminal. Therefore, ...
Page 10
... For optimal circuit performance, the TS1101 should be in very close proximity to the external current- sense resistor and the pcb tracks from RSENSE to the RS+ and the RS- input terminals of the TS1101 should be short and symmetric. Also recommended are a ground plane and surface mount resistors and capacitors ...
Page 11
... Alder Drive, Milpitas, CA 95035 +1 (408) 215 - 1220 ▪ www.touchstonesemi.com (N.B., Drawings are not to scale) 2.80 - 3.00 0.950 TYP. 0.300(MIN) 0.500(MAX) 10° TYP. (2 Plcs) 1.50 – 1.75 10° TYP. 10° TYP. (2 Plcs) (2 Plcs) TS1101 0.950 TYP. 10° TYP. (2 Plcs) 0.50 -0.70 0.09 – 0.127 0.25 0° ~ 8° Guage 0.30 - 0.55 Plane Page 11 TS1101DS r1p0 RTFDS ...