TS8GCF600 TRANSCEND [Transcend Information. Inc.], TS8GCF600 Datasheet - Page 9
TS8GCF600
Manufacturer Part Number
TS8GCF600
Description
600X CompactFlash Card
Manufacturer
TRANSCEND [Transcend Information. Inc.]
Datasheet
1.TS8GCF600.pdf
(87 pages)
- Current page: 9 of 87
- Download datasheet (3Mb)
T
Signal Description
A10 – A00
(PC Card Memory Mode)
A10 – A00
(PC Card I/O Mode)
A02 - A00
(True IDE Mode)
BVD1
(PC Card Memory Mode)
-STSCHG
(PC Card I/O Mode)
Status Changed
-PDIAG
(True IDE Mode)
BVD2
(PC Card Memory Mode)
-SPKR
(PC Card I/O Mode)
-DASP
(True IDE Mode)
-CD1, -CD2
(PC Card Memory Mode)
-CD1, -CD2
(PC Card I/O Mode)
-CD1, -CD2
(True IDE Mode)
Transcend Information Inc.
T
T
S
S
S
8
8
8
Signal Name
G
G
G
~
~
~
3
3
3
2
2
2
G
G
G
C
C
C
F
F
F
6
6
6
0
0
0
0
0
0
Dir.
I/O
I/O
O
I
I
14,15,16,17,
8,10,11,12,
26,25
18,19,20
18,19,20
46
45
Pin
These address lines along with the -REG signal are used to select the following:
The I/O port address registers within the CompactFlash Storage Card , the
memory mapped port address registers within the CompactFlash Storage Card,
a byte in the card's information structure and its configuration control and status
registers.
This signal is the same as the PC Card Memory Mode signal.
In True IDE Mode, only A[02:00] are used to select the one of eight registers
in the Task File, the remaining address lines should be grounded by the
host.
This signal is asserted high, as BVD1 is not supported.
This signal is asserted low to alert the host to changes in the READY and Write
Protect states, while the I/O interface is configured. Its use is controlled by the
Card Config and Status Register.
In the True IDE Mode, this input / output is the Pass Diagnostic signal in the
Master / Slave handshake protocol.
This signal is asserted high, as BVD2 is not supported.
This line is the Binary Audio output from the card. If the Card does not support
the Binary Audio function, this line should be held negated.
In the True IDE Mode, this input/output is the Disk Active/Slave Present signal in
the Master/Slave handshake protocol.
These Card Detect pins are connected to ground on the CompactFlash Storage
Card. They are used by the host to determine that the CompactFlash Storage
Card is fully inserted into its socket.
This signal is the same for all modes.
This signal is the same for all modes.
9
Description
600X CompactFlash Card
V1.0
Related parts for TS8GCF600
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8A SCRS
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
Transcend 44-pin Ide Flash Module
Manufacturer:
Transcend Information. Inc.
Datasheet:
Part Number:
Description:
Transcend Industrial Cf Card
Manufacturer:
Transcend Information. Inc.
Datasheet:
Part Number:
Description:
Transcend Industrial Cf Card
Manufacturer:
Transcend Information. Inc.
Datasheet:
Part Number:
Description:
Transcend 40-pin Ide Flash Module
Manufacturer:
Transcend Information. Inc.
Datasheet:
Part Number:
Description:
2GB/4GB USB Flash Drive
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
Industrial CF Card
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
266X CompactFlash Card
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
industrial CompactFlash Card
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
40-Pin IDE Flash Module (Horizontal)
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
40-Pin IDE Flash Module
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
44-Pin IDE Flash Module(Horizontal)
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
44-Pin IDE Flash Module
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet:
Part Number:
Description:
300X CompactFlash Card
Manufacturer:
TRANSCEND [Transcend Information. Inc.]
Datasheet: