SST49LF004B-33-4C-WHE SST [Silicon Storage Technology, Inc], SST49LF004B-33-4C-WHE Datasheet - Page 9

• Manufacturer Part Number: SST49LF004B-33-4C-WHE
• Description: 4 Mbit Firmware Hub
• Manufacturer: SST [Silicon Storage Technology, Inc]

4 Mbit Firmware Hub
SST49LF004B
Clock
The LCLK pin accepts a clock input from the host controller.
Input/Output Communications
The LAD[3:0] pins are used to serially communicate cycle
information such as cycle type, cycle direction, ID selection,
address, data, and sync fields.
Input Communication Frame
The LFRAME# pin is used to indicate start of a LPC bus
cycle. The pin is also used to abort an LPC bus cycle in
progress.
Interface Mode Select
The MODE pin is used to set the interface mode. If the
mode pin is set to logic high, the device is in PP mode. If
the mode pin is set low, the device is in the LPC mode. The
mode selection pin must be configured prior to device oper-
ation. The mode pin is internally pulled down if the pin is left
unconnected.
Reset
A V
and RST# pins have the same function internally. It is
required to drive INIT# or RST# pins low during a system
reset to ensure proper CPU initialization. During a Read
operation, driving INIT# or RST# pins low deselects the
device and places the output drivers, LAD[3:0], in a high
impedance state. The reset signal must be held low for a
minimum of time T
cedure is performed during a Program or Erase operation.
See Tables 19 and 20, Reset Timing Parameters, for more
information. A device reset during an active Program or
Erase operation will abort the operation and memory con-
tents may become invalid due to data being altered or cor-
rupted from an incomplete Erase or Program operation.
Identification Inputs
These pins are part of a mechanism that allows multiple
devices to be attached to the same bus. The strapping of
these pins is used to identify the component. The boot
device must have ID[3:0] = 0; all subsequent devices
should use sequential count-up strapping. These pins are
internally pulled-down with a resistor between 20-100 K
©2006 Silicon Storage Technology, Inc.
IL
on INIT# or RST# pin initiates a device reset. INIT#
RSTP
. A reset latency occurs if a reset pro-
Ω
.
9
General Purpose Inputs
The General Purpose Inputs (GPI[4:0]) can be used as dig-
ital inputs for the CPU to read. The GPI register holds the
values on these pins. The data on the GPI pins must be
stable before the start of a GPI register Read and remain
stable until the Read cycle is complete. The pins must be
driven low, V
Write Protect / Top Block Lock
The Top Boot Lock (TBL#) and Write Protect (WP#) pins
are provided for hardware write protection of device mem-
ory in the SST49LF004B. The TBL# pin is used to write
protect 16 boot sectors (64 KByte) at the highest memory
address range for the SST49LF004B. The WP# pin write
protects the remaining sectors in the flash memory.
An active low signal at the TBL# pin prevents Program and
Erase operations of the top boot block. When TBL# pin is
held high, the hardware write protection of the top boot
block is disabled. The WP# pin serves the same function for
the remaining blocks of the device memory. The TBL# and
WP# pins write protection functions operate independently
of one another. Both TBL# and WP# pins must be set to
their required protection states prior to starting a Program or
Erase operation. A logic level change occurring at the TBL#
or WP# pin during a Program or Erase operation could
cause unpredictable results.
Row / Column Select
The R/C# pin is used to control the multiplex address
inputs in Parallel Programming (PP) mode. The column
addresses are mapped to the higher internal address
(A
internal addresses (A
Output Enable
The OE# pin is used to gate the output data buffers in PP
mode.
Write Enable
The WE# pin is used to control the write operations in PP
mode.
No Connection
These pins are not connected internally.
18-11
), and the row addresses are mapped to the lower
IL
, or high, V
10-0
IH
).
but not left unconnected (float).
Preliminary Specifications
S71307-02-000
2/06