VT33N3 PERKINELMER [PerkinElmer Optoelectronics], VT33N3 Datasheet - Page 68
![no-image](/images/no-image-200.jpg)
VT33N3
Manufacturer Part Number
VT33N3
Description
Photoconductive Cells and Analog Optoisolators (Vactrols)
Manufacturer
PERKINELMER [PerkinElmer Optoelectronics]
Datasheet
1.VT33N3.pdf
(76 pages)
- Current page: 68 of 76
- Download datasheet (2Mb)
Application Notes—Analog Optical Isolators
Variable bandwidth can be avoided if the AOI is used in a voltage
divider circuit at the input of a fixed gain amplifier. For the same range
of input signals, the amplifier gain must be 500 and the voltage divider
must have a range of 1000:1. This configuration is shown in Figure 5.
The AOI has been changed to a lower resistance unit to be able to
work over the wider range. Also, A
non-inverting stage to avoid a high insertion loss. This circuit is useful
when the input voltage is high, which allows the use of a lower gain
amplifier.
Speaker Power Limiting
Speakers that are driven from high power amplifiers must be protected
from excess drive. While ordinary program levels may be well within
the rating of the speaker, peaks do occur that can be destructive. The
simplest solution is to use a compressor or limiter. Unfortunately, the
maximum power that may be applied is not constant over the
frequency range. Therefore, the limit must be set to provide protection
at the lowest frequency that is expected.
To understand the requirements for effective speaker protection, a brief
review of speaker power limitations follows. Figure 7 is a typical
maximum sine wave voltage limit for a low frequency speaker
commonly called a “woofer”. Above 200 Hz, the maximum allowed
voltage or power is constant. The operating temperature at which wire
insulation and coil bonding fail establishes this value. Below 200 Hz,
1
is now a high input impedance,
Figure 5. Peak Sensing Compressor with Constant Bandwidth
63
the voltage limit is determined by the allowable diaphragm excursion.
For constant voltage on the speaker, the displacement doubles when
the frequency is reduced by half. The maximum displacement is
determined by the mechanical design of the speaker and exceeding
the limit will produce extreme distortion and may even cause
mechanical damage.
Figure 7. Maximum sine wave Voltage and Power for a Typical Woofer
Related parts for VT33N3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![VT60-525](/images/no-image3.png)
Part Number:
Description:
Vt-series Triple Output 15w ~ 60w
Manufacturer:
TDK Corp.
Datasheet:
![SUV-2000NIL](/images/no-image3.png)
Part Number:
Description:
Lamps for Photolithography
Manufacturer:
PERKINELMER [PerkinElmer Optoelectronics]
Datasheet:
![VTT1017](/images/no-image3.png)
Part Number:
Description:
.050 NPN Phototransistors
Manufacturer:
PERKINELMER [PerkinElmer Optoelectronics]
Datasheet:
![VTT1227](/images/no-image3.png)
Part Number:
Description:
.025 NPN Phototransistors
Manufacturer:
PERKINELMER [PerkinElmer Optoelectronics]
Datasheet:
![PI74LPT16373A](/images/no-image3.png)
Part Number:
Description:
Fast CMOS 3.3V 16-BitTransparent Latch
Manufacturer:
PERKINELMER [PerkinElmer Optoelectronics]
Datasheet:
![ZS1052-12](/images/no-image3.png)
Part Number:
Description:
ZS1052-12
Manufacturer:
PERKINELMER [PerkinElmer Optoelectronics]
Datasheet:
![EGL3840](/images/no-image3.png)
Part Number:
Description:
Egl3840
Manufacturer:
PerkinElmer Optoelectronics
Datasheet:
![CRS20](/images/no-image3.png)
Part Number:
Description:
Ceramic Chip SMD Reflective Sensor
Manufacturer:
PerkinElmer Optoelectronics
Datasheet:
![RL1024D](/images/no-image3.png)
Part Number:
Description:
Gap/Reflective Sensor - Datasheet Reference
Manufacturer:
PerkinElmer Optoelectronics
![RL1024PAQ-712](/images/no-image3.png)
Part Number:
Description:
P-SERIES LINEAR PHOTODIODE ARRAY IMAGERS
Manufacturer:
PerkinElmer Optoelectronics
![RL1024PAQ-021](/images/no-image3.png)
Part Number:
Description:
P-Series Linear Photodiode Array Imagers
Manufacturer:
PerkinElmer Optoelectronics
![RL1201LGO-711](/images/no-image3.png)
Part Number:
Description:
Linear CMOS spectroscopy sensor. 25 microm pitch, 2.5 mm aperture, 128 photodiode elements.
Manufacturer:
PerkinElmer Optoelectronics
![VT300CT](/images/no-image3.png)
Part Number:
Description:
Photoconductive Cells and Analog Optoisolators (Vactrols)
Manufacturer:
PerkinElmer Optoelectronics
Datasheet:
![MD1342](/images/no-image3.png)
Part Number:
Description:
Ultra High Sensitivity Gateable Channel Photomultiplier DC-Modules
Manufacturer:
PerkinElmer Optoelectronics
Datasheet:
![VT300](/images/no-image3.png)
Part Number:
Description:
Photoconductive Cells and Analog Optoisolators (vactrols)
Manufacturer:
PerkinElmer Optoelectronics