MIC2208 MICREL [Micrel Semiconductor], MIC2208 Datasheet - Page 11

• Manufacturer Part Number: MIC2208
• Description: 3mmx3mm 1MHz 3A PWM Buck Regulator
• Manufacturer: MICREL [Micrel Semiconductor]

Since the MIC2208 uses an internal P-channel
MOSFET, Rdson losses are inversely proportional to
supply voltage. Higher supply voltage yields a higher
gate to source voltage, reducing the Rdson,
reducing the MOSFET conduction losses. A graph
showing typical Rdson vs input supply voltage can
be found in the typical characteristics section of this
datasheet.
Diode conduction losses occur due to the forward
voltage drop (V
power losses can be approximated as follows:
For this reason, the Schottky diode is the rectifier of
choice. Using the lowest forward voltage drop will
help reduce diode conduction losses, and improve
efficiency.
Duty cycle, or the ratio of output voltage-to-input
voltage, determines whether the dominant factor in
conduction losses will be the internal MOSFET or
the Schottky diode. Higher duty cycles place the
power losses on the high side switch, and lower duty
cycles place the power losses on the schottky diode.
Inductor conduction losses (P
by multiplying the DC resistance (DCR) times the
square of the output current;
Also, be aware that there are additional core losses
associated with switching current in an inductor.
Since most inductor manufacturers do not give data
on the type of material used, approximating core
losses becomes very difficult, so verify inductor
temperature rise.
Switching losses occur twice each cycle , when
the switch turns on and when the switch turns off.
This is caused by a non-ideal world where switching
transitions are not instantaneous, and neither are
currents. Figure 6 demonstrates (Or exaggerates.)
how switching losses due to the transitions dissipate
power in the switch.
September 2005
Where D is the duty cycle.
P
P
P
SW
D
L
=
=
DCR
=
V
F
R
×
DSON
I
×
OUT
I
F
OUT
) and the output current. Diode
×
×
I
2
OUT
(
1
−
D
2
)
×
D
L
) can be calculated
11
Normally, when the switch is on, the voltage across
the switch is low (virtually zero) and the current
through the switch is high. This equates to low
power dissipation. When the switch is off, voltage
across the switch is high and the current is zero,
again with power dissipation being low. During the
transitions, the voltage across the switch (V
the current through the switch (I
causing
instantaneous power point. During continuous mode,
these losses are the highest. Also, with higher load
currents, these losses are higher. For discontinuous
operation, the transition losses only occur during the
“off” transition since the “on” transitions there is no
current flow through the inductor.
Component Selection
Input Capacitor
A 10µF ceramic is recommended on each VIN pin
for bypassing.
recommended
dielectrics lose most of their capacitance over
temperature and are therefore, not recommended.
Also, tantalum and electrolytic capacitors alone are
not recommended due their reduced RMS current
handling, reliability, and ESR increases.
An additional 0.1µF is recommended close to the
VIN and PGND pins for high frequency filtering.
Smaller case size capacitors are recommended due
to their lower ESR and ESL. Please refer to layout
recommendations for proper layout of the input
capacitor.
Inductor Selection
The MIC2208 is designed for use with a 1µH
inductor. Proper selection should ensure the
inductor can handle the maximum average and peak
currents required by the load. Maximum current
ratings of the inductor are generally given in two
methods; permissible DC current and saturation
current. Permissible DC current can be rated either
Figure 6. Switching Transition Losses
the
transition
for
X5R or X7R dielectrics are
the
input
to
S-D
be
capacitor.
) are at middle,
www.micrel.com
M9999-092905
the
S-D
highest
) and
Y5V