MIC2205-1.38YML MICREL [Micrel Semiconductor], MIC2205-1.38YML Datasheet

no-image

MIC2205-1.38YML

Manufacturer Part Number
MIC2205-1.38YML
Description
2MHz PWM Synchronous Buck Regulator with LDO Standby Mode
Manufacturer
MICREL [Micrel Semiconductor]
Datasheet
General Description
The Micrel MIC2205 is a high efficiency 2MHz PWM
synchronous
features a LOWQ™ LDO standby mode that draws
only 18µA of quiescent current.
allows an ultra-low noise, small size, and high
efficiency solution for portable power applications.
In PWM mode, the MIC2205 operates with a
constant frequency 2MHz PWM control. Under light
load conditions, such as in system sleep or standby
modes, the PWM switching operation can be
disabled to reduce switching losses.
load LOWQ™ mode, the LDO maintains the output
voltage and draws only 18µA of quiescent current.
The LDO mode of operation saves battery life while
not introducing spurious noise and high ripple as
experienced with pulse skipping or bursting mode
regulators.
The MIC2205 operates from 2.7V to 5.5V input and
features internal power MOSFETs that can supply
up to 600mA output current in PWM mode. It can
operate with a maximum duty cycle of 100% for use
in low-dropout conditions.
The MIC2205 is available in the 3mm x 3mm MLF-
10L package with a junction operating range from
–40°C to +125°C.
Data sheets and support documentation can be
found on Micrel’s web site at www.micrel.com.
____________________________________________________________________________________________________
Typical Application
Patent Pending
LOWQ is a trademark of Micrel, Inc
April 2005
Micrel, Inc • 2180 Fortune Drive • San Jose, Ca 95131 • USA • tel +1 (408) 944-0800 • fax +1 (408) 474-1000 • http://www.micrel.com
2.7V to 5.5V
Adjustable Output Buck Regulator with LOWQ™ Mode
GND
V
IN
1µF
C1
buck
0.1µF
LowQ
C2
(step-down)
8
4
6
7
3
VIN
AVIN
EN
LOWQ
BIAS
PGND
10
MIC2205
AGND
1
LDO
SW
regulator
FB
The MIC2205
9
2
5
In this light
R1
100k
R2
125k
2.2µH
that
C3
100pF
C4
2.2µF
V
GND
OUT
Features
• 2.7 to 5.5V supply voltage
• Light load LOWQ™ LDO mode
• 2MHz PWM mode
• Adjustable output voltage option down to 1V
• Ultra-fast transient response
• Stable with 1µF ceramic output capacitor
• Fully integrated MOSFET switches
• Micropower shutdown
• Thermal shutdown and current limit protection
• Pb-free 3mm x 3mm MLF-10L package
• –40°C to +125°C junction temperature range
Applications
• Cellular phones
• PDAs
• USB peripherals
Regulator with LDO Standby Mode
2MHz PWM Synchronous Buck
18µA quiescent current
Low noise, 75µVrms
Output current to 600mA
>95% efficiency
100% maximum duty cycle
Fixed output voltage options available
100
MIC2205
95
90
85
80
75
70
65
60
55
50
0
100 200 300 400 500 600
1.8V
OUTPUT CURRENT (mA)
V
IN
V
= 4.2V
IN
OUT
= 3.6V
V
IN
Efficiency
= 3V
www.micrel.com
M9999-041105

Related parts for MIC2205-1.38YML

MIC2205-1.38YML Summary of contents

Page 1

... PWM mode. It can operate with a maximum duty cycle of 100% for use in low-dropout conditions. The MIC2205 is available in the 3mm x 3mm MLF- 10L package with a junction operating range from –40°C to +125°C. Data sheets and support documentation can be found on Micrel’ ...

Page 2

... Micrel, Inc. Ordering Information Part Number MIC2205-1.3YML MIC2205-1.38YML MIC2205-1.5YML MIC2205-1.58YML MIC2205-1.8YML MIC2205-1.85YML MIC2205YML Note: 1. Other Voltage options available. Contact Micrel for details. Pin Configuration Pin Description Pin Number Pin Name 1 AGND 2 LDO 3 BIAS 4 AVIN 5 FB ...

Page 3

... V EN LOWQ ) .............. –40°C to +125°C J 3x3 MLF-10L (θ ) ................................... 60°C/W JA Min Typ 2.7 2.45 2.55 100 690 16 0.01 0. 100mA 0.13 LOAD 0.2 0.1 100 0.4 0.4 1.8 2 0.5 0.85 0.1 0.5 0.85 0.1 110 MIC2205 IN < +125°C J Max Units 5 900 µA 29 µA 5 µA 1. 0 Ω 2.2 MHz 1 µA 1 µA ...

Page 4

... Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value that is initially measured differential. For outputs below 2.7V, the dropout voltage is the input-to-output voltage differential with a minimum input voltage of 2.7V. April 2005 = 2.2μF, 10Hz to 100kHz OUT = 0V (LDO Mode) OUT 4 MIC2205 Min Typ Max Units µVrms 75 60 120 mA ° ...

Page 5

... OUTPUT CURRENT (mA) Peak Current Limit vs. Supply Voltage 1200 1000 800 600 400 200 LowQ = 2.7 3.4 4.1 4.8 5.5 SUPPLY VOLTAGE (V) 5 MIC2205 1.8V Efficiency OUT 100 3. 4. 100 200 300 400 500 600 OUTPUT CURRENT (mA) 1 ...

Page 6

... Micrel, Inc. Typical Characteristics – PWM Mode (cont.) Turn-On Time vs. Supply Voltage 100 3. 2.7 3.4 4.1 4.8 5.5 SUPPLY VOLTAGE (V) April 2005 6 MIC2205 M9999-041105 www.micrel.com ...

Page 7

... TEMPERATURE (°C) Turn-On Time vs. Supply Voltage 100 3. LowQ = 0V 0 2.7 3.4 4.1 4.8 5.5 SUPPLY VOLTAGE (V) 7 MIC2205 Dropout vs. Output Current 250 200 150 100 3.3V OUT 100 OUTPUT CURRENT (mA) Dropout Voltage vs. Temperature ...

Page 8

... OUTPUT CURRENT (mA) April 2005 Quiescent Current vs. Supply Voltage 100 A OUT 16 LowQ = 0V 15 2.7 3.4 4.1 4.8 5.5 SUPPLY VOLTAGE (V) 8 MIC2205 Quiescent Current vs. Output Current 3. LowQ = 100 OUTPUT CURRENT (mA) M9999-041105 www.micrel.com ...

Page 9

... Control Logic LOWQ SGND April 2005 HSD PWM Anti-Shoot Control Through LSD N-Channel Current Limit Bias, UVLO, Soft Thermal Start Shutdown LDO Block LDO Current Limit MIC2205 Block Diagram 9 P-Channel Current Limit 1.0V EA 1.0V LDO PGND M9999-041105 www.micrel.com MIC2205 V OUT C OUT ...

Page 10

... Micrel, Inc. Functional Characteristics Load Transient PWM Mode Time 20 s/div Enable Transient PWM Mode Time 40 s/div April 2005 LowQ = V IN LowQ = 0V 10 MIC2205 M9999-041105 www.micrel.com ...

Page 11

... Micrel, Inc. Functional Characteristics April 2005 11 MIC2205 M9999-041105 www.micrel.com ...

Page 12

... SGND Signal ground (SGND) is the ground path for the biasing and control circuitry. The current loop for the signal ground should be separate from the Power ground (PGND) loop. considerations for more details. 12 MIC2205 significantly reduced. ) can be calculated as FF Refer to the layout M9999-041105 www ...

Page 13

... Smaller case size capacitors are recommended due to there lower ESR and ESL. Inductor Selection The MIC2205 is designed for use with a 2.2µH inductor. Proper selection should ensure the inductor can handle the maximum average and peak currents required by the load. Maximum current ratings of the inductor are generally given in two methods ...

Page 14

... Micrel, Inc. Layout Recommendations Note: The above figures demonstrate the recommended layout for the MIC2205 adjustable option. April 2005 MIC2205 Top MIC2205 Bottom 14 MIC2205 V OUT GND V IN LowQ EN V OUT GND V IN LowQ EN M9999-041105 www.micrel.com ...

Page 15

... C4 R2 2.2µF 125k GND 2.2µH V OUT C3 100pF C4 2.2µF GND Manufacturer AVX (4) Murata AVX (4) Murata (3) Vishay AVX (4) Murata (4) Murata (2) Sumida (3) Vishay Dale (3) Vishay Dale (3) Vishay Dale (3) Vishay Dale (3) Vishay Dale (3) Vishay Dale TM (5) Micrel, Inc. M9999-041105 www.micrel.com MIC2205 Qty ...

Page 16

... A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. April 2005 10-Lead MLF™ (ML) © 2004 Micrel, Incorporated. 16 MIC2205 M9999-041105 www.micrel.com ...

Related keywords