AS1100PE-Z AMSCO [austriamicrosystems AG], AS1100PE-Z Datasheet
AS1100PE-Z
Related parts for AS1100PE-Z
AS1100PE-Z Summary of contents
Page 1
Data Sheet AS1100 Serially Interfaced, 8-Digit LED Driver AS1100 Key Features 10MHz Serial Interface - Individual LED Segment Control - Decode/No-Decode Digit Selection - 20µA Low-Power Shutdown (Data Retained) - Extremely low Operating Current 0.5mA in open loop - Digital ...
Page 2
Data Sheet AS1100 Absolute Maximum Ratings Voltage (with respect to GND) VDD DIN, CLK, LOAD All Other Pins Current DIG0–DIG7 Sink Current SEGA–G, DP Source Current Continuous Power Dissipation (TA = +85°C) Narrow Plastic DIP (derate 13.3mW/°C above +70°C Wide ...
Page 3
Data Sheet AS1100 Parameter Symbol Conditions Input Current DIN, CLK, LOAD I IH Logic High Input Voltage V Logic Low Input Voltage V Output High Voltage V Output Low Voltage V Hysteresis Voltage Timing Characteristics CLK Clock Period t CLK ...
Page 4
Data Sheet AS1100 LOAD CLK DIN D15 DOUT Figure 1: Timing diagram D15 D14 D13 D12 D11 D10 Address Table 1: Serial data format (16 bits) Detailed Description Serial-Addressing Modes Programming of ...
Page 5
Data Sheet AS1100 Decode-Mode Register In the AS1100 a BCD decoder is included. Every digit can be selected via register 09h to be decoded. The BCD code consists of the numbers 0-9, E,H, L,P and -. In register 09h a ...
Page 6
Data Sheet AS1100 Decode Mode decode for digits 7– Code B decode for digit decode for digits 7–1 Code B decode for digits 3– decode for digits 7–4 ...
Page 7
Data Sheet AS1100 Figure 2: Standard 7-segment LED Duty Cycle Hex Code 1/32 (min on 3/ ...
Page 8
Data Sheet AS1100 Display Test Register With the display test register 0Fh all LED can be tested. In the test mode all LEDs are switched on at maximum brightness (duty cycle 31/32). All programming of digit and control registers is ...
Page 9
Data Sheet AS1100 8x8 LED Dot Matrix Driver The example in Figure 3 uses the AS1100 to drive an 8x8 LED dot matrix. The LED columns have common cathode and are connected to the DIG0-7 outputs. The rows are connected ...
Page 10
Data Sheet AS1100 Computing Power Dissipation The upper limit for power dissipation (PD) for the AS1100 is determined from the following equation (VDD x 0.5mA) + (VDD - V )(DUTY x I LED where: VDD = supply voltage ...
Page 11
Data Sheet AS1100 Inches Millimeters Dim Min Max Min Max A --- 0.180 --- 4.572 A1 0.015 --- 0.380 --- A2 0.125 .0175 3.180 4.450 A3 0.055 0.080 1.400 2.030 B 0.015 0.022 0.381 0.560 B1 0.045 0.065 1.140 1.650 ...
Page 12
... Temp Range Pin Package AS1100PL 0°C to +70°C 24 Narrow Plastic DIP AS1100WL 0°C to +70°C 24 Wide SO Tubes AS1100PE -40°C to +85°C 24 Narrow Plastic DIP AS1100WE -40°C to +85°C 24 Wide SO Tubes AS1100WL-T 0°C to +70°C 24 Wide SO T&R AS1100WE-T -40°C to +85°C 24 Wide SO T&R For Pb-free package use suffix ‘ ...