LTAGL LINER [Linear Technology], LTAGL Datasheet
LTAGL
Related parts for LTAGL
LTAGL Summary of contents
Page 1
FEATURES ■ V Range: 0.9V to 10V IN ■ Minimum Input Voltage: 0.9V ■ Dropout Voltage: 150mV Typical ■ Output Current: 100mA ■ Adjustable Output ( REF OUT(MIN) ■ Fixed Output Voltages: 1.2V, 1.5V, 1.8V ■ Stable with ...
Page 2
... ORDER PART NUMBER LT3020EMS8 OUT 1 OUT 2 OUT 3 GND 4 MS8 PACKAGE MS8 PART MARKING 8-LEAD PLASTIC MSOP T = 150°C, θ JMAX LTAGL SEE THE APPLICATIONS INFORMATION SECTION ORDER PART NUMBER TOP VIEW LT3020EDD-1 LT3020EDD-1 LT3020EDD-1 SHDN DD8 PART MARKING ...
Page 3
ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are T PARAMETER CONDITIONS Minimum Input Voltage (Note 14 100mA, T LOAD I = 100mA, T LOAD ADJ Pin Voltage (Notes 4, ...
Page 4
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1.8 ELECTRICAL CHARACTERISTICS The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are T PARAMETER CONDITIONS Current Limit (Note 12 10V OUT(NOMINAL) Input Reverse Leakage Current ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS ADJ Pin Voltage 206 I = 1mA L 204 202 200 198 196 194 –50 – 100 125 TEMPERATURE (°C) 3020 G04 Output Voltage 1.230 I = 1mA L ...
Page 6
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1 TYPICAL PERFOR A CE CHARACTERISTICS GND Pin Current 2500 V OUT = 1.5V (LT 3020-1.5) 2250 T = 25°C J 2000 R = 15Ω L 1750 I = 100mA L 1500 1250 R = 30Ω L ...
Page 7
W U TYPICAL PERFOR A CE CHARACTERISTICS Input Ripple Rejection 100 1.5V + 0.5V RIPPLE 120Hz IN P 0.5V 10 OUT I = 100mA L ...
Page 8
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1 CTIO S OUT (Pins 1, 2): These pins supply power to the load. Use a minimum output capacitor of 2.2µF to prevent oscillations. Applications with large load transients require larger out- put capacitors ...
Page 9
U U APPLICATIO S I FOR ATIO The LT3020 is a very low dropout linear regulator capable of 1V input supply operation. Devices supply 100mA of output current and dropout voltage is typically 150mV. Quiescent current is typically 120µA and ...
Page 10
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1 APPLICATIO S I FOR ATIO 20 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10µF 0 X5R –20 –40 –60 Y5V –80 –100 BIAS VOLTAGE (V) Figure 2. Ceramic ...
Page 11
U U APPLICATIO S I FOR ATIO The LT3020 regulator has internal thermal limiting (with hysteresis) designed to protect the device during overload conditions. For normal continuous conditions, do not exceed the maximum junction temperature rating of 125°C. Carefully consider ...
Page 12
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1 APPLICATIO S I FOR ATIO The LT3020 incurs no damage if OUT is pulled below ground left open circuit or grounded, OUT can be pulled below ground by 10V. No current flows from ...
Page 13
U U APPLICATIO S I FOR ATIO If the LT3020 is powered by a battery mounted in close proximity on the same circuit board, a 2.2µF input capaci- tor is sufficient for stability. However, if the LT3020 is powered by ...
Page 14
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1.8 PACKAGE DESCRIPTIO 3.5 ±0.05 1.65 ±0.05 2.15 ±0.05 (2 SIDES) 0.25 ± 0.05 0.50 BSC 2.38 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS Package 8-Lead Plastic DFN (3mm × 3mm) (Reference LTC DWG ...
Page 15
PACKAGE DESCRIPTIO 0.889 ± 0.127 (.035 ± .005) 5.23 3.20 – 3.45 (.206) (.126 – .136) MIN 0.65 0.42 ± 0.038 (.0256) (.0165 ± .0015) BSC TYP RECOMMENDED SOLDER PAD LAYOUT NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO ...
Page 16
LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1.8 RELATED PARTS PART NUMBER DESCRIPTION LT1121/LT1121HV 150mA, Micropower LDOs LT1129 700mA, Micropower LDO LT1761 100mA, Low Noise Micropower LDO LT1762 150mA, Low Noise Micropower LDO LT1763 500mA, Low Noise Micropower LDO LT1764/LT1764A 3A, Low Noise, Fast Transient Response ...