NIPCI-6030E NI [National Instruments Corporation], NIPCI-6030E Datasheet - Page 8

• Manufacturer Part Number: NIPCI-6030E
• Description: Full-Featured E Series Multifunction DAQ 12 or 16-Bit, up to 1.25 MS/s, up to 64 Analog Inputs
• Manufacturer: NI [National Instruments Corporation]

236
12-Bit E Series Multifunction
DAQ Specifications
Specifications – NI 607xE, NI 606xE, NI 6040E, NI 602xE
Digital I/O
Compatibility .................................................... 5 V TTL
Power-on state ................................................. Input; (high-impedance)
Digital logic levels
Transfer rate (1 word = 8 bits)
Constant sustainable rate................................ 1 to 10 kwords/s, system dependent
Timing I/O
Number of channels
Resolution
Compatibility .................................................... 5 V/TTL
Base clocks available
Base clock accuracy ......................................... ±0.01%
Maximum source frequency
Minimum source pulse duration ...................... 10 ns, edge-detect mode
Minimum gate pulse duration.......................... 10 ns, edge-detect mode
Data transfers .................................................. DMA*, interrupts, programmed I/O
*Except DAQCard and USB DAQPad
National Instruments • Tel: [phone] • Fax: [phone] • [e-mail] • ni.com
6025E
All others
Level
Input low voltage
Input high voltage
Output low voltage (I
Output high voltage (I
Level
Input low voltage
Input high voltage
Output low voltage (Iout = 2.5 mA)
Output high voltage (Iout = -2.5 mA)
6025E
All others
DAQPad-6070E
All others
P0.<0..7>
P1.<0..7>, P2.<0..7>, P3.<0..7>
Maximum with NI-DAQ, system dependent
Up/down counter/timers ........................... 2
Frequency scaler........................................ 1
Up/down counter/timers ........................... 24 bits
Frequency scaler........................................ 4 bits
Up/down counter/timers ........................... 20 MHz and 100 kHz
Frequency scaler........................................ 10 MHz and 100 kHz
Up/down counter/timers ........................... 20 MHz
out
out
Number of Channels
= 24 mA)
= -13 mA)
Data Transfers
Transfer Rate
Interrupts, programmed I/O
Programmed I/O
32 input/output
8 input/output
50 kwords/s
5 kwords/s
Minimum (V)
Minimum (V)
4.35
2.0
2.2
3.7
0
–
0
–
Maximum (V)
Maximum (V)
0.8
5.0
0.4
0.8
5.0
0.4
–
–
Triggers
Analog Triggers
Purpose
Source............................................................... All analog input channels, PFI 0/AI START TRIG
Level
Slope................................................................. Positive or negative; software selectable
Resolution......................................................... 8 bits, 1 in 256
Bandwidth (-3 dB)
Hysteresis......................................................... Programmable
Digital Triggers (All Devices)
Purpose
Source............................................................... PFI <0..9>, RTSI <0..6>
Compatibility .................................................... 5 V/TTL
Response .......................................................... Rising or falling edge
Pulse width....................................................... 10 ns minimum
External Input For Digital Or Analog Trigger (PFI0/TRIG1)
Impedance
Coupling............................................................ DC
Protection
Calibration
Recommended warm-up time.......................... 15 minutes; 30 minutes for DAQCard and DAQPad
Calibration interval........................................... 1 year
Onboard calibration reference
607xE
6062E
6040E
602xE
Device
607xE
6062E
6040E
Analog input .............................................. Start and stop trigger, gate, clock
Analog output ............................................ Start trigger, gate, clock
General-purpose counter/timers ............... Source, gate
Internal source, AI<0..15/63>.................... ±Full-scale
External source, PFI 0/AI START TRIG .......... ±10 V
Analog input .............................................. Start and stop trigger, gate, clock
Analog output ............................................ Start trigger, gate, clock
General-purpose counter/timers ............... Source, gate
6062E ......................................................... 12 kΩ
607xE, 6040E ............................................. 10 kΩ
Digital trigger ............................................ -0.5 to V
DC level ..................................................... 5.000 V (±3.5 mV) over full operating temperature,
Temperature coefficient ............................ ±5 ppm/°C maximum
Long-term stability .................................... ±15 ppm/ 1000 h
(continued)
Number of Triggers
None
1
Internal Source
500 kHz
650 kHz
2 MHz
actual value stored in EEPROM
cc
+ 0.5 V
External Source
2.5 MHz
7 MHz
3 MHz