NIPCI-6509 NI [National Instruments Corporation], NIPCI-6509 Datasheet - Page 4

• Manufacturer Part Number: NIPCI-6509
• Description: Low-Cost Industrial Digital I/O-5 V TTL/CMOS
• Manufacturer: NI [National Instruments Corporation]

Low-Cost Industrial Digital I/O – 5 V TTL/CMOS
Specifications
These specifications are typical at 25 °C unless otherwise noted.
Digital I/O
Number of channels............................ 96 I/O
Compatibility ....................................... TTL/CMOS
Power-on state.................................... Inputs high-Z (default), user-
Data transfers ..................................... Interrupts, programmed I/O
I/O connector ...................................... 100-pin female 0.050 series SCSI
Digital Logic Levels
Input signals
Output signals (V
Power Requirements
Power consumption (typical)............... 375 mA on + 3.3 VDC
No load current ................................... 250 mA on + 5 VDC
With a load, use the following equation to determine the power
consumption on a 5 V rail. In the equation j is the number of the channels
you are using to source current.
250 mA + ∑ (current sourced on channel i)
Power available at I/O connector....... 1 A (fused), maximum
Note: The voltage at the I/O connector is dependent on the
amount of current drawn from an NI 6509.
Level
Input voltage (V
Input logic low-voltage (V
Input logic high-voltage (V
The maximum input logic high and output logic high voltages assume a V
Given a V
5.5 V with respect to GND.
Level
High-level output current (I
Low-level output current (I
Output voltage (V
Output low voltage (V
Output high voltage (V
The total current sinking/sourcing from one port cannot exceed 100 mA.
Pins 49 and 99 (at +5 V) ................. 1.0 A, maximum
CC
supply voltage of 5.0 V, the absolute maximum voltage rating for each I/O line is -0.5 to
i=1
j
I
)
O
)
CC
OL
OH
), at 24 mA
), at -24 mA
=5 V)
IL
IH
OL
OH
)
)
)
)
Min
selectable input, output 1 or 0
(combined or individually)
(combined or individually)
0 V
2 V
–
3.7 V
Min
–
–
–
0
CC
supply voltage of 5.0 V.
0.8 V
Max
-24 mA
V
24 mA
0.55 V
Max
–
CC
V
–
CC
Physical
Dimensions
Environmental
NI 6509 devices are intended for indoor use only.
Operating temperature ....................... 0 to 55 °C
Storage temperature........................... -20 to 70 °C
Relative humidity ................................ 10 to 90%, noncondensing
Pollution degree.................................. 2
Safety
This product is designed to meet the requirements of the following
standards of safety for electrical equipment for measurement, control,
and laboratory use:
• IEC 61010-1, EN 61010-1
• UL 61010-1, CSA 61010-1
Note: For UL and other safety certifications, refer to the product label or
visit ni.com/certification, search by model number or product line, and
click the appropriate link in the Certification column.
Electromagnetic Compatibility
This product is designed to meet the requirements of the following
standards of EMC for electrical equipment for measurement, control,
and laboratory use:
• EN 61326 EMC requirements; Minimum Immunity
• EN 55011 Emissions; Group 1, Class A
• CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A
Note: For EMC compliance, operate this device according to
product documentation.
CE Compliance
This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:
• 2006/95/EC; Low-Voltage Directive (safety)
• 2004/108/EC; Electromagnetic Compatibility Directive (EMC)
Note: Refer to the Declaration of Conformity (DoC) for this product for
any additional regulatory compliance information. To obtain the DoC for
this product, visit ni.com/certification, search by model number or
product line, and click the appropriate link in the Certification column.
PCI................................................... 12.4 by 9.7 cm (4.9 by 3.8 in.)
PXI................................................... 16.0 by 10.0 cm (6.3 by 3.9 in.)
BUY ONLINE at ni.com or CALL 800 813 3693 (U.S.)
4