ICS1892 Integrated Circuit Systems, ICS1892 Datasheet - Page 38
![no-image](/images/no-image-200.jpg)
ICS1892
Manufacturer Part Number
ICS1892
Description
10Base-T/100Base-TX Integrated PHYceiver
Manufacturer
Integrated Circuit Systems
Datasheet
1.ICS1892.pdf
(148 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ICS1892Y
Manufacturer:
ICS
Quantity:
20 000
- Current page: 38 of 148
- Download datasheet (817Kb)
7.2.4 Auto-Negotiation: Reset and Restart
7.2.4.1 Auto-Negotiation Reset
7.2.4.2 Auto-Negotiation Restart
ICS1892, Rev. D, 2/26/01
If enabled, execution of the ICS1892 auto-negotiation process occurs at power-up and upon management
request. There are two primary ways to begin the Auto-Negotiation state machine:
•
•
During a reset, the ICS1892 initializes its Auto-Negotiation sublayer modules to their default states. (That
is, the Auto-Negotiation Arbitration State Machine and the Auto-Negotiation Progress Monitor reset to their
idle states.) In addition, the Auto-Negotiation Progress Monitor status bits are all set to logic zero. This
action occurs for any type of reset (hardware reset, software reset, or power-on reset).
As with a reset, during an Auto-Negotiation restart, the ICS1892 initializes the Auto-Negotiation Arbitration
State Machine and the Auto-Negotiation Progress Monitor modules to their default states. However, during
an Auto-Negotiation Restart, the Auto-Negotiation Progress Monitor status bits maintain their current state.
Only three events can alter the state of the Auto-Negotiation Progress Monitor status bits after a Restart:
(1) an STA read operation, (2) a reset, or (3) the Auto-Negotiation Arbitration State Machine progressing to
a higher state or value.
The Auto-Negotiation Progress Monitor Status bits change only if they are progressing to a state with a
value greater than their current state (that is, a state with a higher logical value than that of their current
state). For a detailed explanation of these bits and their operation, see
Progress
After the Auto-Negotiation Arbitration State Machine reaches its final state (which is Auto-Negotiation
Complete), only an STA read of the QuickPoll Detailed Status Register or an ICS1892 reset can alter these
status bits.
Any one of the following situations initiate a restart of the ICS1892 Auto-Negotiation sublayer:
•
•
•
ICS1892 reset
Auto-Negotiation Restart
A link failure
In software mode (that is, HW/SW pin is logic one), either of the following actions initiate a restart of the
ICS1892 Auto-Negotiation sublayer:
In hardware mode (that is, HW/SW pin is a logic zero), toggling the ANSEL (Auto-Negotiation Select) pin
from a logic one to a logic zero, and back to a logic one.
– Writing a logic one to the Control Register’s Restart Auto-Negotiation bit (bit 0.9), which is a self-
– Toggling the Control Register’s Auto-Negotiation Enable bit (bit 0.12) from a logic one to a logic zero,
ICS1892 Data Sheet
clearing bit.
and back to a logic one.
Monitor”.
© 2000-2001, Integrated Circuit Systems, Inc.
All rights reserved.
38
Section 7.2.5, “Auto-Negotiation:
Chapter 7 Functional Blocks
February 26, 2001
Related parts for ICS1892
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ICM7101D](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7111](/images/no-image3.png)
Part Number:
Description:
Speech And Ringer Ic With Digital Volume Control
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7102](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7115](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic With Volume Control
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7102b](/images/no-image3.png)
Part Number:
Description:
Low Cost Single Chip Telephone Ic
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7600](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Voltage Output Quad Dacs With Parallel Interface
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![AD583](/images/manufacturer_photos/0/0/56/analog_devices_tmb.jpg)
Part Number:
Description:
IC Sample and Hold Gated OP Amp
Manufacturer:
Analog Devices
Datasheet:
![ICM202B](/images/no-image3.png)
Part Number:
Description:
CIF/QCIF CMOS image sensor
Manufacturer:
IC Media
Datasheet:
![ICM7561](/images/no-image3.png)
Part Number:
Description:
(ICM7521 - ICM7561) 12/10/8-Bit Low Power Single DAC
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7562](/images/no-image3.png)
Part Number:
Description:
(ICM7522 - ICM7562) 12/10/8-Bit Low Power Dual DACs
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![ICM7563](/images/no-image3.png)
Part Number:
Description:
(ICM7523 - ICM7563) 12/10/8-Bit Low Power Quad DACs
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7521](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Single Dac With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7522](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Dual Dacs With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7523](/images/no-image3.png)
Part Number:
Description:
12/10/8-bit Low Power Quad Dacs With Serial Interface And Voltage Output
Manufacturer:
IC MICROSYSTEMS
Datasheet:
![icm7363](/images/no-image3.png)
Part Number:
Description:
Quad 12/10/8-bit Voltage-output Dacs
Manufacturer:
IC MICROSYSTEMS
Datasheet: