SL6609AKGNPDE MITEL [Mitel Networks Corporation], SL6609AKGNPDE Datasheet
SL6609AKGNPDE
Related parts for SL6609AKGNPDE
SL6609AKGNPDE Summary of contents
Page 1
This device is an advanced direct conversion receiver for operation up to 470MHz. The design is based on the SL6609 receiver and is a pin for pin product upgrade. The device integrates all functions to translate a binary FSK modulated ...
Page 2
SL6609A ELECTRICAL CHARACTERISTICS These characteristics are guaranteed over the following conditions unless otherwise stated: Tamb = 25 C, VCC1 = 1.3V, VCC2 = 2.7V Characteristics VCC1 - Supply voltage VCC2 - Supply voltage 21,27,28 ICC1 - Supply current 11,13,14 ICC2 ...
Page 3
ELECTRICAL CHARACTERISTICS These characteristics are guaranteed over the following conditions unless otherwise stated: Tamb = 25 C, VCC1 = 1.3V, VCC2 = 2.7V Characteristics Battery Economy Input logic high Input logic low Input current Input current Battery Flag Input Input ...
Page 4
SL6609A RECEIVER CHARACTERISTICS (Demonstration board) Measurement conditions unless stated V Carrier frequency 282MHz, BER 1 in 30, Tamb = 25 C (TPx/TPy typically:- 160mV 10% for - 73dBm RF input to the LNA) PP Characteristics Sensitivity Intermodulation (IP3) Intermodulation (IP2) ...
Page 5
OPERATION OF SL6609A The SL6609A is a Direct Converson Receiver designed for use up to 470MHz available pin SSOP package and it integrates all the facilities required for the conversion FSK signal ...
Page 6
SL6609A 6 Fig.3 Application circuit board ...
Page 7
COMPONENTS LIST FOR APPLICATION BOARD (LO Circuit in Fig.3) Resistors R1 open circuit R2 open circuit R3 100 R4 100k 100 R8 open circuit R9 220k R10 1M (6) R11 100k R12 not used (1) ...
Page 8
SL6609A COMPONENTS LIST FOR APPLICATION BOARD (LO circuit is 50 network as in Fig.5 - crystal oscillator not specified) Resistors R1 open circuit R2 open circuit R3 100 R4 100k R5 100 R6 100 R7 100 R8 open circuit R9 ...
Page 9
RF Amplifier Components Values Resistors R14, R15 4k7 R13 see note 1 R22 47k Notes: (1) The value of R13 is determined by the set up procedure (See "Set up for optimum performance"). (2) C20 and C21 are purely for ...
Page 10
SL6609A Vcc1 current source pin 8 R16 -120 -115 -110 -105 10 Vr C15 - Pin 28 L2 100k + Pin 9 Ctc Rdecay C8 ...
Page 11
S11 FREQ MAG 0.969 50.000 0.958 100.000 0.942 150.000 0.917 200.000 0.893 250.000 0.858 300.000 350.000 0.832 0.806 400.000 450.000 0.781 0.755 500.000 550.000 0.743 0.725 600.000 650.000 0.703 0.680 700.000 750.000 0.666 0.653 800.000 850.000 0.636 0.615 900.000 950.000 ...
Page 12
SL6609A Conditions:- 282MHz demonstration board i.e. 20dB LNA, 2dB noise figure, carrier frequency 282MHz, 1200bps baud rate, 4kHz deviation frequency, BER 1 in 30. 12 Fig.10a AC parameters vs. supply and temperature Vcc1 = 1.0V, Vcc2 = 1.8V Vcc1 = ...
Page 13
Conditions:- 282MHz demonstration board i.e. 20dB LNA, 2dB noise figure, carrier frequency 282MHz, 1200bps baud rate, 4kHz deviation frequency, BER 1 in 30. Fig.10b AC parameters vs. supply and temperature SL6609A Vcc1 = 1.0V, Vcc2 = 1.8V Vcc1 = 1.3V, ...
Page 14
SL6609A Conditions:- ICC1 includes 500 A LNA current but does not include the regulator supply (audio AGC inactive). ICC2 measured with BATT FLAG and DATA O/P HIGH 282MHz. Note 1- IP3 is level above wanted needed to reduce ...
Page 15
Fig.12 Sensitivity, IP3 vs Receiver Gain Fig.13 Sensitivity, adjacent Channel vs Receiver Gain SL6609A 15 ...
Page 16
SL6609A - ...
Page 17
SL6609A 17 ...
Page 18
SL6609A PACKAGE DETAILS Dimensions are shown thus: mm (in) 10·07/10·33 (0·396/0·407) 28 5·20/5·38 PIN 1 IDENT (0·205/0·212) 1 1·68/1·78 (0·066/0·070) 28 LEADS AT 0·65 (0·0256) NOM. SPACING 28-LEAD SHRUNK MINIATURE PLASTIC DIL (SSOP) - NP28 HEADQUARTERS OPERATIONS MITEL SEMICONDUCTOR Cheney ...