MAXQ622G-0000 MAXIM [Maxim Integrated Products], MAXQ622G-0000 Datasheet

no-image

MAXQ622G-0000

Manufacturer Part Number
MAXQ622G-0000
Description
16-Bit Microcontrollers with Infrared Module and Optional USB
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAXQ622G-0000
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAXQ622G-0000+
Manufacturer:
Maxim Integrated
Quantity:
10 000
19-5117; Rev 2; 5/11
The MAXQ612/MAXQ622 are low-power, 16-bit MAXQ
microcontrollers designed for low-power applications
including universal remote controls, consumer elec-
tronics, and white goods. Both devices use a low-
power, high-throughput, 16-bit RISC microcontroller.
Serial peripherals include two universal synchronous/
asynchronous receiver-transmitters (USARTs), two SPIK
master/slave communications ports, and an inter-inte-
grated circuit (I
an IR module with carrier frequency generation and
flexible port I/O capable of multiplexed keypad control.
The MAXQ622 adds a universal serial bus (USB) with
integrated physical interface (PHY).
The MAXQ612/MAXQ622 include 128KB of flash memory
and 6KB of data SRAM. Intellectual property (IP) protection is
provided by a secure memory management unit (MMU) that
supports multiple application privilege levels and protects
code against copying and reverse engineering. Privilege
levels enable vendors to provide libraries and applications to
execute on the MAXQ612/MAXQ622, while limiting access
to only data and code allowed by their privilege level.
For the ultimate in low-power battery-operated perfor-
mance, the devices include an ultra-low-power stop mode
(0.3FA typical). In this mode, the minimum amount of
circuitry is powered. Wake-up sources include external
interrupts, the power-fail interrupt, and a timer interrupt.
The microcontroller runs from a wide operating voltage of
1.70V to 3.6V, and can also be powered from the USB.
MAXQ is a registered trademark of Maxim Integrated
Products, Inc. SPI is a trademark of Motorola, Inc.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, go to: www.maxim-ic.com/errata.
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
Ordering Information/Selector Guide
data sheet.
Remote Controls
Battery-Powered Portable Equipment
Consumer Electronics
Home Appliances
White Goods
2
C) bus. The devices also incorporate
_______________________________________________________________ Maxim Integrated Products 1
General Description
Infrared Module and Optional USB
appears at end of
Applications
16-Bit Microcontrollers with
M
S
S
S
S
S
S
S
S
S
S
S
S
S
S
High-Performance, Low-Power, 16-Bit RISC Core
DC to 12MHz Operation Across Entire Operating Range
1.70V to 3.6V Operating Voltage
Can Be Powered from Battery (V
33 Total Instructions for Simplified Programming
Three Independent Data Pointers Accelerate Data
Movement with Automatic Increment/Decrement
Dedicated Pointer for Direct Read from Code Space
16-Bit Instruction Word, 16-Bit Data Bus
16 x 16-Bit General-Purpose Working Registers
Secure MMU for Application Partitioning and IP
Protection
Memory Features
USB Features (MAXQ622 Only)
Additional Peripherals
Low Power Consumption
128KB Flash Memory
6KB Data SRAM
USB 2.0 Full-Speed Compatible
Hardware Receive and Transmit Buffers for High
Integrated Full-Speed Transceiver
On-Chip Termination and Pullup Resistors
Power-Fail Warning
Power-On Reset (POR)/Brownout Reset
Automatic IR Carrier Frequency Generation and
Two 16-Bit Programmable Timers/Counters with
Two SPI Communication Ports
Two USART Communication Ports
I
Programmable Watchdog Timer
8kHz Nanopower Ring Oscillator Wake-Up Timer
Up to 56 General-Purpose I/O
0.3µA (typ), 3µA (max) in Stop Mode
4.8mA (typ) at 12MHz, 520µA (typ) at 1MHz in
2
C Port
Throughput
Modulation
Prescaler and Capture/Compare
T
Active Mode
512-Byte Sectors
20,000 Erase/Write Cycles per Sector
A
= +25NC, Power-Fail Monitor Disabled
DD
) or USB (V
Features
DDB
)

Related parts for MAXQ622G-0000

MAXQ622G-0000 Summary of contents

Page 1

Rev 2; 5/11 Infrared Module and Optional USB General Description The MAXQ612/MAXQ622 are low-power, 16-bit MAXQ microcontrollers designed for low-power applications including universal remote controls, consumer elec- tronics, and white goods. Both devices use a low- power, high-throughput, 16-bit ...

Page 2

Microcontrollers with Infrared Module and Optional USB Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3

Infrared Module and Optional USB TABLE OF CONTENTS (continued) Power-Fail Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4

Microcontrollers with Infrared Module and Optional USB ABSOLUTE MAXIMUM RATINGS Voltage Range on V with Respect to GND .....-0.3V to +3.6V DD Voltage Range on Any Lead with Respect to GND Except V .............. -0. BUS Voltage ...

Page 5

Infrared Module and Optional USB RECOMMENDED OPERATING CONDITIONS (continued 3.6V 0NC to +70NC.) (Note 1) DD RST A PARAMETER SYMBOL Input Hysteresis (Schmitt) V IHYS Input Low Voltage for HFXIN V IL_HFXIN Input High ...

Page 6

Microcontrollers with Infrared Module and Optional USB RECOMMENDED OPERATING CONDITIONS (continued 3.6V 0NC to +70NC.) (Note 1) DD RST A PARAMETER SYMBOL System Clock Period t CK NANOPOWER RING Nanopower Ring Frequency f ...

Page 7

Infrared Module and Optional USB RECOMMENDED OPERATING CONDITIONS (continued 3.6V 0NC to +70NC.) (Note 1) DD RST A PARAMETER SYMBOL Single-Ended Receiver V Threshold Single-Ended Receiver V SEH Hysteresis Differential Output Signal V CRS ...

Page 8

Microcontrollers with Infrared Module and Optional USB RECOMMENDED OPERATING CONDITIONS (continued 3.6V 0NC to +70NC.) (Note 1) DD RST A PARAMETER SYMBOL MOSI_ Input to SCLK_ Sample t SIS Edge Rise/Fall Setup MOSI_ ...

Page 9

Infrared Module and Optional USB BUS CONTROLLER TIMING (Notes 6, 21) (Figure 2) PARAMETER Bus Operating Frequency System Frequency Bit Rate Hold Time After (Repeated) START Clock Low Period Clock High ...

Page 10

Microcontrollers with Infrared Module and Optional USB Note 15: For USB operation, both V DD Note 16: FRCVDD is the force V power-supply bit (PWCN.10). When FRCVDD = always used as the core 3V power ...

Page 11

Microcontrollers with Infrared Module and Optional USB TOP VIEW P1.1/INT1 34 P1.2/INT2 35 P1.3/INT3 36 P1.4/INT4 37 P1.5/INT5 38 P1.6/INT6 39 P1.7/INT7 40 GND 41 IRTX 42 IRRX 43 + P0.0/IRTXM 44 *EXPOSED PAD. ______________________________________________________________________________________ Pin Configurations P3.4/INT12 22 ...

Page 12

Microcontrollers with Infrared Module and Optional USB TOP VIEW P1.2/INT2 49 P1.3/INT3 50 P1.4/INT4 51 P1.5/INT5 52 P1.6/INT6 53 P1.7/INT7 54 P4.0 55 P4.1 56 P4.2 57 P4.3 58 P4.4 59 P4.5 60 P4.6 61 P4.7 62 GND 63 ...

Page 13

Infrared Module and Optional USB TOP VIEW P1.2/INT2 49 P1.3/INT3 50 P1.4/INT4 51 P1.5/INT5 52 P1.6/INT6 53 P1.7/INT7 54 P4.0 55 P4.1 56 P4.2 57 P4.3 58 P4.4 59 P4.5 60 P4.6 61 P4.7 62 GND 63 IRTX 64 PIN ...

Page 14

Microcontrollers with Infrared Module and Optional USB PIN MAXQ612 MAXQ612 MAXQ622 TQFN-EP LQFP LQFP — — 19 — — 16 — — 18 — — 20 — — ...

Page 15

Infrared Module and Optional USB PIN MAXQ612 MAXQ612 MAXQ622 TQFN-EP LQFP LQFP GENERAL-PURPOSE I/O AND SPECIAL FUNCTION PINS 44, 1–7 2– 2– 33–40 45, 48–54 45, 48–54 ______________________________________________________________________________________ 16-Bit Microcontrollers with Pin Descriptions—TQFN, LQFP (continued) NAME ...

Page 16

Microcontrollers with Infrared Module and Optional USB PIN MAXQ612 MAXQ612 MAXQ622 TQFN-EP LQFP LQFP 11–14, 11–14, 8–11, 29–32 41–44 41–44 18–25 27–34 27–34 16 _____________________________________________________________________________________ Pin Descriptions—TQFN, LQFP (continued) NAME General-Purpose, Digital, I/O, Type C Port. These port pins ...

Page 17

Infrared Module and Optional USB PIN MAXQ612 MAXQ612 MAXQ622 TQFN-EP LQFP LQFP — 55-62 55–62 — 37–40 37–40 16–21, 36, 26, 27 36, 46, 47 46, 47 — — — ______________________________________________________________________________________ 16-Bit Microcontrollers with Pin Descriptions—TQFN, LQFP (continued) NAME General-Purpose, ...

Page 18

Microcontrollers with Infrared Module and Optional USB PIN NAME MAXQ612 MAXQ622 23, 30, 45, 8, 30, 45, 73 GND REG18 21 21 RESET 31 31 HFXIN 32 32 HFXOUT — ...

Page 19

Infrared Module and Optional USB PIN NAME MAXQ612 MAXQ622 74 74 IRTX 75 75 IRRX GENERAL-PURPOSE I/O AND SPECIAL FUNCTION PINS P0.0–P0.7; IRTXM, RX0, TX0, RX1 TX1, SDA ...

Page 20

Microcontrollers with Infrared Module and Optional USB PIN NAME MAXQ612 MAXQ622 P2.0–P2.7; MOSI0, 16, 18, 19, 16, 18, 19, MISO0, 20, 50, 51, 20, 50, 51, SCLK0, 53, 54 53, 54 SSEL0, TCK, TDI, TMS, TDO 33–37, 39, P3.0–P3.7; ...

Page 21

Infrared Module and Optional USB PIN NAME MAXQ612 MAXQ622 P5.0–P5.3; MOSI1, 46–49 46–49 MISO1, SCLK1, SSEL1 12–15, 38, 12–15, 41–44 P6.0–P6.7 41, 43 11, 17, 4, 11, 17, 52, 22–27, 52, N.C. 57, 64 57, 64 Detailed Description ...

Page 22

Microcontrollers with Infrared Module and Optional USB stop-mode current increases battery life over competing microcontrollers. An integrated POR circuit with brownout support resets the device to a known condition following a power-up cycle or brownout condition. Additionally, a power- ...

Page 23

Infrared Module and Optional USB ROM consists of subroutines that can be called from application software. These include the following: • In-system programming (bootstrap loader) using JTAG interface • In-circuit debug routines • Test routines (internal memory tests, memory loader, ...

Page 24

Microcontrollers with Infrared Module and Optional USB The IR timer is composed of a carrier generator and a carrier modulator. The carrier generation module uses the 16-bit IR carrier register (IRCA) to define the high and low time of ...

Page 25

Infrared Module and Optional USB 2) Transfers its current IRV value to the IRMT. 3) Resets IRV content to 0000h (if IRXRL = 1). 4) Continues counting again until the next qualified event. If the IR timer value rolls over ...

Page 26

Microcontrollers with Infrared Module and Optional USB • Programmable 9th bit parity support • Start/stop bit support Serial Peripheral Interface (SPI) The dual-integrated SPI interfaces provide independent serial communication channels that communicate syn- chronously with peripheral devices in a ...

Page 27

Infrared Module and Optional USB pin to GND. The clock source should be driven through a CMOS driver. If the clock driver is a TTL gate, its output must be connected to V through a pullup resistor to DD ensure ...

Page 28

Microcontrollers with Infrared Module and Optional USB DEBUG SERVICE MAXQ612 ROUTINES MAXQ622 (UTILITY ROM) DEBUG ENGINE TMS CONTROL TAP TCK BREAKPOINT CONTROLLER TDI ADDRESS TDO Figure 4. In-Circuit Debugger master that can either be automatic test equipment or a ...

Page 29

Infrared Module and Optional USB Table 4. Power-Fail Warning Level Selection PFW THRESHOLD PWCN.PFWARNCN[1: mode to minimize power consumption. This feature is enabled using the power-fail monitor disable (PFD) bit in the PWCN register. The reset ...

Page 30

Microcontrollers with Infrared Module and Optional USB Table 5. Power-Fail Detection States During Normal Operation INTERNAL STATE POWER-FAIL REGULATOR A On Off Off (Periodically) G ...

Page 31

Infrared Module and Optional USB V t < PFW V RST B V POR STOP INTERNAL RESET (ACTIVE HIGH) Figure 6. Stop Mode Power-Fail Detection States with Power-Fail Monitor Enabled Table 6. Stop Mode Power-Fail Detection ...

Page 32

Microcontrollers with Infrared Module and Optional USB PFW B V RST V POR STOP INTERNAL RESET (ACTIVE HIGH) INTERRUPT Figure 7. Stop Mode Power-Fail Detection with Power-Fail Monitor Disabled Table 7. Stop Mode Power-Fail Detection ...

Page 33

Infrared Module and Optional USB Table 7. Stop Mode Power-Fail Detection States with Power-Fail Monitor Disabled (continued) INTERNAL STATE POWER-FAIL REGULATOR D Off Off On E Off (Periodically) F Off Off Applications Information The low-power, high-performance RISC architecture of this ...

Page 34

... MAXQ612G-0000+ 0NC to +70NC MAXQ622G-0000+ 0NC to +70NC Note: The 4-digit suffix “-0000” indicates a microcontroller in the default state with the flash memory unprogrammed. Any value other than 0000 indicates a device preprogrammed at Maxim with proprietary customer-supplied software. For more information on factory preprogramming of these devices, contact Maxim at https://support ...

Page 35

Infrared Module and Optional USB REVISION REVISION NUMBER DATE 0 2/10 Initial release Changed the V 1 5/10 Recommended Operating Conditions table 2 5/11 Added the Pin Descriptions—Bare Die table Maxim cannot assume responsibility for use of any circuitry other ...

Related keywords