XE8806A SEMTECH [Semtech Corporation], XE8806A Datasheet - Page 67
XE8806A
Manufacturer Part Number
XE8806A
Description
Ultra Low-Power Low-Voltage
Manufacturer
SEMTECH [Semtech Corporation]
Datasheet
1.XE8806A.pdf
(143 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XE8806AMI026TLF
Manufacturer:
MAXIM
Quantity:
230
- Current page: 67 of 143
- Download datasheet (895Kb)
Note: Depending on the status of the EnResetPConf bit in RegSysCtrl, RegPAEdge, RegPADebounce and
RegPACtrl can be reset by any of the possible system resets or only with power-on reset and NRESET pad.
11.4 Interrupts and events map
11.5 Port A (PA) Operation
The Port A input status (debounced or not) can be read from RegPAin.
Debounce mode:
Each bit in Port A can be individually debounced by setting the corresponding bit in RegPADebounce. After reset,
the debounce function is disabled. After enabling the debouncer, the change of the input value is accepted only if
height consecutive samples are identical. Selection of the clock is done by bit DebFast in Register RegPACtrl.
Note: The tolerance on the debounce frequency depends on the selected clock source. When the external clock is
used, the pulse width will be correct if the input of the low prescaler is set to a frequency close to 32kHz (see clock
block documentation).
Pullups/Snap-to-rail:
Different functions are possible depending on the value of the registers RegPAPullup and RegPASnaptorail.
When the corresponding bit in RegPAPullup is set to 0, the inputs are floating (pullup and pulldown resistors are
disconnected). When the corresponding bit in RegPAPullup is 1 and in RegPASnaptorail is 0, a pullup resistor is
connected to the input pin. Finally, when the corresponding bit in RegPAPullup is 1 and in RegPASnaptorail is 1,
the snap-to-rail function is active.
© Semtech 2006
pos.
pos.
7:1
7:0
0
Interrupt source
pa_irqbus[5]
pa_irqbus[4]
pa_irqbus[1]
pa_irqbus[0]
pa_irqbus[7]
pa_irqbus[6]
pa_irqbus[3]
pa_irqbus[2]
RegPACtrl
RegPASnaptorail
PASnaptorail[7:0]
DebFast
[7:1]
RegIrqMid[5]
RegIrqMid[4]
RegIrqMid[1]
RegIrqMid[0]
RegIrqLow[7]
RegIrqLow[6]
RegIrqLow[3]
RegIrqLow[2]
the interrupt manager
Default mapping in
DebFast
rw
r
r w
rw
rw
Table 11-10: debounce frequency selection
0
1
reset
0000000
0 nresetpconf
reset
0 nresetpconf
Table 11-9: RegPASnaptorail
Table 11-8: RegPACtrl
11-4
Clock filter
RegEvn[4]
RegEvn[0]
Default mapping in the
32kHz
1kHz
description
description
event manager
0 = slow debounce, 1 = fastdebounce
set snap-to-rail input on
Unused
XE8806A/XE8807A
www.semtech.com
Related parts for XE8806A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: