PIC12F609-I/PQTP MICROCHIP [Microchip Technology], PIC12F609-I/PQTP Datasheet - Page 3

• Manufacturer Part Number: PIC12F609-I/PQTP
• Description: 8-Pin Flash-Based, 8-Bit CMOS Microcontrollers
• Manufacturer: MICROCHIP [Microchip Technology]

High-Performance RISC CPU:
• Only 35 instructions to learn:
• Operating speed:
• Interrupt capability
• 8-level deep hardware stack
• Direct, Indirect and Relative Addressing modes
Special Microcontroller Features:
• Precision Internal Oscillator:
• Power-Saving Sleep mode
• Voltage range:
• Industrial and Extended Temperature range
• Power-on Reset (POR)
• Power-up Timer (PWRT) and Oscillator Start-up
• Brown-out Reset (BOR)
• Watchdog Timer (WDT) with independent
• Multiplexed Master Clear with pull-up/input pin
• Programmable code protection
• High Endurance Flash:
Low-Power Features:
• Standby Current:
• Operating Current:
• Watchdog Timer Current:
© 2006 Microchip Technology Inc.
- All single-cycle instructions except branches
- DC – 20 MHz oscillator/clock input
- DC – 200 ns instruction cycle
- Factory calibrated to ±1%, typical
- Software selectable frequency: 4 MHz or
- PIC12F609/615: 2.0V to 5.5V
- PIC12HV609/615: 2.0V to user defined
Timer (OST)
oscillator for reliable operation
- 100,000 write Flash endurance
- Flash retention: > 40 years
- 50 nA @ 2.0V, typical
- 11 A @ 32 kHz, 2.0V, typical
- 260 A @ 4 MHz, 2.0V, typical
- 1 A @ 2.0V, typical
Note:
8 MHz
maximum (see note)
Voltage across the shunt regulator should
not exceed 5V.
8-Pin Flash-Based, 8-Bit CMOS Microcontrollers
PIC12F609/615/12HV609/615
Preliminary
Peripheral Features:
• Shunt Voltage Regulator (PIC12HV609/615 only):
• 5 I/O pins and 1 input only
• High current source/sink for direct LED drive
• Analog Comparator module with:
• Timer0: 8-bit timer/counter with 8-bit
• Enhanced Timer1:
• In-Circuit Serial Programming
PIC12F615/HV615 ONLY:
• Enhanced Capture, Compare, PWM module:
• A/D Converter:
• Timer2: 8-bit timer/counter with 8-bit period
- 5 volt regulation
- 4 mA to 50 mA shunt range
- Interrupt-on-pin change or pins
- Individually programmable weak pull-ups
- One analog comparator
- Programmable on-chip voltage reference
- Comparator inputs and output externally
- Built-In Hysteresis (software selectable)
programmable prescaler
- 16-bit timer/counter with prescaler
- External Timer1 Gate (count enable)
- Option to use OSC1 and OSC2 in LP mode
- Option to use system clock as Timer1
pins
- 16-bit Capture, max. resolution 12.5 ns
- Compare, max. resolution 200 ns
- 10-bit PWM with 1 or 2 output channels, 1
- 10-bit resolution and 4 channels, samples
register, prescaler and postscaler
(CV
accessible
as Timer1 oscillator if INTOSC mode
selected
output channel programmable “dead time”,
max. frequency 20 kHz, auto-shutdown
internal voltage references
REF
) module (% of V
DD
)
TM
(ICSP
DS41302A-page 1
TM
) via two