PIC17C43 MICROCHIP [Microchip Technology], PIC17C43 Datasheet - Page 21
![no-image](/images/no-image-200.jpg)
PIC17C43
Manufacturer Part Number
PIC17C43
Description
High-Performance 8-Bit CMOS EPROM/ROM Microcontroller
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.PIC17C43.pdf
(240 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC17C43-16/L
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC17C43-16/P
Manufacturer:
Microchip Technology
Quantity:
135
Company:
Part Number:
PIC17C43-16/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC17C43-16/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC17C43-16E/L
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC17C43-16E/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC17C43-25/L023
Manufacturer:
RICHTEK
Quantity:
3 000
- Current page: 21 of 240
- Download datasheet (2Mb)
5.0
The PIC17C4X devices have 11 sources of interrupt:
• External interrupt from the RA0/INT pin
• Change on RB7:RB0 pins
• TMR0 Overflow
• TMR1 Overflow
• TMR2 Overflow
• TMR3 Overflow
• USART Transmit buffer empty
• USART Receive buffer full
• Capture1
• Capture2
• T0CKI edge occurred
There are four registers used in the control and status
of interrupts. These are:
• CPUSTA
• INTSTA
• PIE
• PIR
The CPUSTA register contains the GLINTD bit. This is
the Global Interrupt Disable bit. When this bit is set, all
interrupts are disabled. This bit is part of the controller
core functionality and is described in the Memory Orga-
nization section.
FIGURE 5-1:
1996 Microchip Technology Inc.
TMR1IF
TMR1IE
INTERRUPTS
TMR2IF
TMR2IE
RBIF
RBIE
INTERRUPT LOGIC
TMR3IF
TMR3IE
RCIF
RCIE
CA2IF
CA2IE
TXIF
TXIE
CA1IF
CA1IE
This document was created with FrameMaker 4 0 4
GLINTD
T0CKIF
T0CKIE
INTF
INTE
PEIF
PEIE
T0IF
T0IE
When an interrupt is responded to, the GLINTD bit is
automatically set to disable any further interrupt, the
return address is pushed onto the stack and the PC is
loaded with the interrupt vector address. There are four
interrupt vectors. Each vector address is for a specific
interrupt source (except the peripheral interrupts which
have the same vector address). These sources are:
• External interrupt from the RA0/INT pin
• TMR0 Overflow
• T0CKI edge occurred
• Any peripheral interrupt
When program execution vectors to one of these inter-
rupt vector addresses (except for the peripheral inter-
rupt address), the interrupt flag bit is automatically
cleared. Vectoring to the peripheral interrupt vector
address does not automatically clear the source of the
interrupt. In the peripheral interrupt service routine, the
source(s) of the interrupt can be determined by testing
the interrupt flag bits. The interrupt flag bit(s) must be
cleared in software before re-enabling interrupts to
avoid infinite interrupt requests.
All of the individual interrupt flag bits will be set regard-
less of the status of their corresponding mask bit or the
GLINTD bit.
For external interrupt events, there will be an interrupt
latency. For two cycle instructions, the latency could be
one instruction cycle longer.
The “return from interrupt” instruction, RETFIE , can be
used to mark the end of the interrupt service routine.
When this instruction is executed, the stack is
“POPed”, and the GLINTD bit is cleared (to re-enable
interrupts).
PIC17C4X
Wake-up (If in SLEEP mode)
or terminate long write
DS30412C-page 21
Interrupt to CPU
Related parts for PIC17C43
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC17C44-16I/P](/photos/6/61/66192/150-40-dip_tmb.jpg)
Part Number:
Description:
IC, 8BIT MCU, PIC17C, 16MHZ, DIP-40
Manufacturer:
Microchip Technology
Datasheet:
![PIC17C756A-16I/L](/photos/12/13/121323/c04-049_l_tmb.jpg)
Part Number:
Description:
IC, 8BIT MCU, PIC17C, 33MHZ, PLCC-64
Manufacturer:
Microchip Technology
Datasheet:
![PIC18F2480](/images/no-image3.png)
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC18F2682-I/PT](/images/no-image3.png)
Part Number:
Description:
28/40/44-Pin Enhanced Flash Microcontrollers with ECAN Technology, 10-Bit A/D and nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![MCP4024](/images/no-image3.png)
Part Number:
Description:
Low-Cost NV Digital POT with WiperLock™ Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC12F1516](/images/no-image3.png)
Part Number:
Description:
28/40/44-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC12F1822](/images/no-image3.png)
Part Number:
Description:
8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC12F1840](/images/no-image3.png)
Part Number:
Description:
8-Pin Flash Microcontrollers with nanoWatt XLP Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![TC1263](/images/no-image3.png)
Part Number:
Description:
500mA Fixed Output CMOS LDO with Shutdown
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![TC1268](/images/no-image3.png)
Part Number:
Description:
500mA Fixed Output, Fast Response CMOS LDO with Shutdown
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![TC4405](/images/no-image3.png)
Part Number:
Description:
1.5A Dual Open-Drain MOSFET Drivers
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![TC4428](/images/no-image3.png)
Part Number:
Description:
1.5A DUAL HIGH-SPEED POWER MOSFET DRIVERS
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![MCP41100](/images/no-image3.png)
Part Number:
Description:
Single/Dual Digital Potentiometer with SPI™ Interface
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet: