DS89C420-ENL MAXIM [Maxim Integrated Products], DS89C420-ENL Datasheet - Page 45
DS89C420-ENL
Manufacturer Part Number
DS89C420-ENL
Description
Ultra-High-Speed Microcontroller
Manufacturer
MAXIM [Maxim Integrated Products]
Datasheet
1.DS89C420-ENL.pdf
(58 pages)
- Current page: 45 of 58
- Download datasheet (670Kb)
NOTES:
1) Specifications to -40°C are guaranteed by design and not production tested.
2) All voltages are referenced to ground.
3) Active current is measured with a 33MHz clock source driving XTAL1, V
4) Idle mode current measured with a 33MHz clock source driving XTAL1, V
5) Stop mode measured with XTAL and RST grounded, V
6) When addressing external memory.
7) RST = 5.5V. This condition mimics the operation of pins in I/O mode.
8) During a 0-to-1 transition, a one-shot drives the ports hard for two clock cycles. This measurement
9) Ports 1, 2, and 3 source transition current when being pulled down externally. The current reaches its
10) This port is a weak address holding latch in bus mode. Peak current occurs near the input transition
11) RST = 5.5V. Port 0 floating during reset and when in the logic- high state during I/O mode.
12) While the specifications for V
13) The user should note that this part is tested and guaranteed to operate down to 4.5V (10%) and that
14) Guaranteed by design.
pins disconnected.
All other pins disconnected.
reflects a port pin in transition mode.
maximum at approximately 2V.
point of the holding latch at approximately 2V.
is not possible. Within the ranges given, there is a guaranteed separation between these two voltages.
V
(min)] where the processor’s operation is not guaranteed, but the reset trip point has not been reached.
This should not be an issue in most applications, but should be considered when proper operation
must be maintained at all times. For these applications, it may be desirable to use a more accurate
external reset.
RST
(min) is specified below that point. This indicates that there is a range of voltages [V
PFW
and V
RST
45 of 58
overlap, the design of the hardware makes it such that this
CC
= 5.5V. All other pins disconnected.
CC
CC
= RST = 5.5V. All other
= 5.5V, RST at ground.
MIN
DS89C420
to V
RST
Related parts for DS89C420-ENL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC MCU 50MHZ ULTRA HS 44-PLCC
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU 50MHZ ULTRA HS 40-DIP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU 50MHZ ULTRA HS 44-TQFP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 33MHZ HP 44-TQFP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 25MHZ HP 44-TQFP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 33MHZ HP 40-DIP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 33MHZ HP 40-DIP
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 33MHZ HP 44-PLCC
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 25MHZ HP 44-PLCC
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
IC MCU ULTRA 33MHZ HP 44-PLCC
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
LCC/M°/CIRCUITI INTEGRATI MAXIM
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
KIT/E/MAXIM ANALOG ESSENTIALS # COLLECTION OF PLUG-IN EVALUATION MODULES
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet: