LMH6601MG NSC [National Semiconductor], LMH6601MG Datasheet - Page 7

• Manufacturer Part Number: LMH6601MG
• Description: 250 MHz, 2.4V CMOS Op Amp with Shutdown
• Manufacturer: NSC [National Semiconductor]

2.7V Electrical Characteristics
V
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of
the device such that T
Note 3: The maximum continuous output current (I
Note 4: Human Body Model is 1.5 kΩ in series with 100 pF. Machine Model is 0Ω in series with 200 pF.
Note 5: SD logic is CMOS compatible. To ensure proper logic level and to minimize power supply current, SD should typically be less than 10% of total supply
voltage away from either supply rail.
Note 6: Typical numbers are the most likely parametric norm. Bold numbers refer to over temperature limits.
Note 7: Negative input current implies current flowing out of the device.
Note 8: Drift determined by dividing the change in parameter at temperature extremes by the total temperature change.
Note 9: Guaranteed by design.
Note 10: “V
I
VOH1
VOH2
VOH3
VOL1
VOL2
VOL3
I
I
Load
R
R
C
VDMAX
VDMIN
I
V
T
T
Isolation
Miscellaneous Performance
S
CC
O
O
i
on
off
_glitch
/2, R
O
O
O
_1
Symbol
_Enable
_Disabled Output Resistance
_Disabled Output Capacitance
L
= 150Ω to V
OFF
ID
” is input differential voltage (input overdrive).
Supply Current
Output High Voltage
(Relative to V
Output Low Voltage
(Relative to V
Output Current
Output Load Rating
Output Resistance
Voltage Limit for Disable (Pin 5) (Note 5)
Voltage Limit for Enable (Pin 5) (Note 5)
Logic Input Current (Pin 5)
Turn-on Glitch
Turn-on Time
Turn-off Time
Off Isolation
J
= T
A
−
. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where T
unless otherwise specified. Boldface limits apply at temperature extremes. (Note 2) (Continued)
Parameter
+
–
)
)
OUT
) is determined by device power dissipation limitations.
Normal Operation
V
Shutdown
SD tied to ≤ 0.27V (Note 5)
R
R
R
R
R
R
V
Respective Supply
V
mV (Note 10)
THD
to V
Enabled, A
Shutdown
Shutdown
SD = 2.7V (Note 5)
1 MHz, R
OUT
L
L
L
L
L
L
OUT
OUT
Single Supply with V
= 150Ω to V
= 75Ω to V
= 10 kΩ to V
= 150Ω to V
= 75Ω to V
= 10 kΩ to V
S
/2, V
<
= V
≤ 0.6V from
= V
−30 dBc, f = 200 kHz, R
S
S
L
OUT
/2
/2, V
V
= 1 kΩ
= +1
Condition
S
S
= 2.2 V
7
ID
/2
/2
–
–
–
–
=
±
18
PP
S
= 2.7V, A
Source
Sink
Source
Sink
L
tied
V
= +2, R
(Note 6)
–260
–420
2.43
Min
–50
100
25
35
0
F
= 604Ω, SD tied to V
(Note 6)
–200
–200
>
+125
Typ
100
–10
760
9.0
0.2
5.6
1.2
5.2
+4
+4
25
62
40
60
100
4
(Note 6)
+125
Max
10.6
12.5
0.27
+45
+45
125
2.7
www.national.com
+
, V
OUT
Units
J
MΩ
mA
mV
mV
mA
nA
pF
pA
dB
µs
ns
>
Ω
Ω
V
V
V
T
=
A
.