V23818-C18-L37 INFINEON [Infineon Technologies AG], V23818-C18-L37 Datasheet
V23818-C18-L37
Related parts for V23818-C18-L37
V23818-C18-L37 Summary of contents
Page 1
... Distance km/ single mode fiber 2) (SMF) 1) Current MSA documentation can be found at www.infineon.com/fiberoptics (Intermediate Reach (ITU-T G.957 (Telcordia GR-253). For ordering information see next page trademark of Lucent. Data Sheet V23818-C18-Lxx/L4xx 1) 1 Fiber Optics File: 1119 File: 1120 2003-06-06 ...
Page 2
... Ordering Information 1) Part Number Range Stock Products V23818-C18-L47 IR V23818-C18-L46 Products on Request V23818-C18-L37 IR V23818-C18-L36 V23818-C18-L45 IR V23818-C18-L49 V23818-C18-L35 IR V23818-C18-L39 V23818-C18-L436 (Intermediate Reach (ITU-T G.957 (Telcordia GR-253). Data Sheet Signal Temperature Data Outputs Detect LVTTL 0°C...70°C –40°C...85°C LVPECL 0° ...
Page 3
... Ground EEt 8 TDis LVTTL input 9 TD+ LVPECL input 10 TD– LVPECL input LVPECL output active high for V23818-C18-L3x/L436. LVTTL output active high for V23818-C18-L4x. Data Sheet TOP VIEW Description Receiver signal ground Receiver power supply ...
Page 4
... For V23818-C18-L3x/L436 use termination and coupling as shown in the termination scheme. RD– / RD+ Receiver data LVPECL level outputs. For V23818-C18-L4x biased and AC coupled internally. For V23818-C18-L3x/L436 use termination and coupling as shown in the termination scheme. TDis A logical LVTTL high input will disable the laser. To enable the laser, an LVTTL low input must be applied ...
Page 5
... ATM switches. This transceiver operates 155.520 Mbit/s from a single power supply (+3.3 V). The full differential data inputs and outputs are LVPECL compatible. Data Sheet V23818-C18-Lxx/L4xx 5 Description 2003-06-06 ...
Page 6
... A high signal on TDis enables the transmitter. If TDis is low or not connected the transmitter is not affected. Data Sheet Automatic Shut-Down Tx Coupling Unit e/o Laser Laser Driver o/e Power Control Monitor Rx Coupling Unit o/e Limiting TIA Amp 6 V23818-C18-Lxx/L4xx Description Single Mode Fiber File: 1351 V ) drops below the reset CCt 2003-06-06 ...
Page 7
... With a field strength of 3 V/m, noise IEC 61000-4-3 frequency ranges from 10 MHz to 2 GHz. No effect on transceiver performance between the specification limits. FCC 47 CFR Part 15, Noise frequency range: Class B 30 MHz to 18 GHz EN 55022 Class B CISPR 22 *) (13.97) .550 7 V23818-C18-Lxx/L4xx Description the receptacle cause no 2003-06-06 File: 1501 ...
Page 8
... Data Input Levels Differential Data Input Voltage Swing Storage Ambient Temperature Hand Lead Soldering Temp/Time Wave Soldering Temp/Time Aqueous Wash Pressure Exceeding any one of these values may destroy the device immediately. Data Sheet V23818-C18-Lxx/L4xx Symbol Limit Values min. max. 0 – ...
Page 9
... CC EE receiver output. Add max for the three outputs. Load V23818-C18-L4x are internally AC coupled. External coupling capacitors required for V23818-C18-L3x/L436. The electro-optical characteristics described in the following tables are valid only for use under the recommended operating conditions. Data Sheet ...
Page 10
... RES ED ITU-T G.957 mask pattern J pk- RMS TDH V TDL t 0.4 ASS t 0.06 DAS and switched on if power supply is above V23818-C18-Lxx/L4xx Technical Data Unit max. –8 dBm 1360 0 µs after t TH RES 2003-06-06 ...
Page 11
... A decrease in optical power of data signal below the specified level will cause the Signal Detect to switch from a high state to a low state. 4) Load is 100 differential. 5) Measured under DC conditions at 25°C. For dynamic measurements a tolerance should be added. 6) Only for V23818-C18-L3x/L436. 7) Only for V23818-C18-L4x. Data Sheet Symbol min ...
Page 12
... Figure 4 Required Labels Indication of laser aperture and beam Figure 5 Laser Emission Data Sheet FDA Class 1 Laser Product Tx Top view Rx 12 V23818-C18-Lxx/L4xx Eye Safety 1300 180 µW 4° IEC File: 1401 File: 1332 2003-06-06 ...
Page 13
... PCB will be half of that in free space. In this scenario even the smallest PCBs may have unexpected resonances. Data Sheet should be placed at the end of each matched resistance can be achieved as follows for V23818-C18-Lxx/L4xx EMI-Recommendations resistor at each (D, Dn and 125 to at Data the r 2003-06-06 ...
Page 14
... TDis 8 TDis CCt CCr C3 C10 RD EEr 14 V23818-C18-Lxx/L4xx SerDes SerDat Out ECL/ PECL Driver SerDat Out Serializer/ Deserializer SerDat In Receiver PLL etc. SerDat In + termination File: 1392 2003-06-06 ...
Page 15
... EEt 9 TD TDis 8 TDis CCt CCr RD EEr 15 V23818-C18-Lxx/L4xx V SerDes SerDat Out ECL/ PECL Driver SerDat Out Serializer/ Deserializer SerDat In Receiver PLL etc. SerDat In + termination 100 EE File: 1393 2003-06-06 ...
Page 16
... Package Outlines Dimensions in mm [inches] Figure 8 Data Sheet V23818-C18-Lxx/L4xx a) recommended bezel position Drawing shown is with collar 16 Package Outlines File: 1212 2003-06-06 ...
Page 17
... Previous Version: Page Subjects (major changes since last revision) Document completely revised; V23818-C18-L79 deleted, V23818-C18-L7xx separated For questions on technology, delivery and prices please contact the Infineon Technologies Offices in Germany or the Infineon Technologies Companies and Representatives worldwide: see our webpage at http://www.infineon.com. ...