MAX4854 MAXIM [Maxim Integrated Products], MAX4854 Datasheet
MAX4854
Related parts for MAX4854
MAX4854 Summary of contents
Page 1
... For over-rail applications, this device passes signals greater than the positive supply (up to +5.5V) through the switch without distortion. The MAX4854 is available in the space-saving, 16-pin, 3mm x 3mm thin QFN package and operates over the -40°C to +85°C extended temperature range. USB Switching ...
Page 2
Quad SPST Switches with Over-Rail Signal Handling ABSOLUTE MAXIMUM RATINGS V , IN_, COM_, NO_ to GND (Note 1) ................-0.3V to +6.0V CC Closed-Switch Continuous Current COM_, NO_, NC_ .....±50mA Peak Current COM_, NO_ (pulsed at 1ms, 50% ...
Page 3
ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V -40°C to +85°C, unless otherwise noted. Typical values are wise noted.) (Note 2) PARAMETER SYMBOL NO_ Off-Capacitance 1MHz, Figure 5 OFF COM On-Capacitance ...
Page 4
... TURN-ON/TURN-OFF TIME vs. TEMPERATURE OFF -40 - TEMPERATURE (°C) LEAKAGE CURRENT vs. TEMPERATURE 1.6 1.4 1.2 COM ON-LEAKAGE 1.0 0.8 COM OFF-LEAKAGE 0.6 0.4 0.2 0 -40 - TEMPERATURE (°C) SWITCH PASSING SIGNALS ABOVE SUPPLY VOLTAGE MAX4854 toc12 2V/div 0V V COM 0V 200µs/div ...
Page 5
PIN NAME 1 NO1 Normally Open Terminal for Analog Switch N.C. No Connection. Not internally connected. Digital Control Input for Analog Switch 2. A logic-low on IN2 disconnects COM2 from NO2 and a 3 IN2 logic-high connects ...
Page 6
... Quad SPST Switches with Over-Rail Signal Handling Detailed Description The MAX4854 low on-resistance, low-voltage, analog switch is designed to operate from a +2V to +5.5V sin- gle supply and is fully specified for nominal +3.0V applications. The device features over-rail signal capa- bility that allows signals up to +5.5V with supply volt- ages down to +2 ...
Page 7
... MAX4854 NO_ V NO IN_ GND LOGIC INPUT C INCLUDES FIXTURE AND STRAY CAPACITANCE OUT Figure 1. Switching Time TxD TxD 39Ω 50pF DELAY DUE TO SWITCH FOR RISING INPUT AND RISING OUTPUT SIGNALS. ...
Page 8
... COM1 IN_ CC MAX4854 NO1* GND MEASUREMENTS ARE STANDARDIZED AGAINST SHORTS AT IC TERMINALS. OFF-ISOLATION IS MEASURED BETWEEN COM_ AND OFF NO_ TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM_ AND ON NO_ TERMINAL ON EACH SWITCH. CROSSTALK IS MEASURED FROM ONE CHANNEL TO THE OTHER CHANNEL. ...
Page 9
... Timing Diagrams (continued 10nF V CC COM_ MAX4854 CAPACITANCE METER NO_ f = 1MHz GND Figure 5. Channel Off-/On-Capacitance _______________________________________________________________________________________ 7 Ω Quad SPST Switches with Over-Rail Signal Handling Test Circuits/ TRANSISTOR COUNT: 735 PROCESS: CMOS Chip Information 9 ...
Page 10
Quad SPST Switches with Over-Rail Signal Handling (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages 0.10 C 0.08 ...
Page 11
For the latest package outline information www.maxim-ic.com/packages.) NOTES: 1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994. 2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES. 3. N IS THE TOTAL NUMBER OF TERMINALS. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE. 5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.20 mm AND 0.25 mm FROM TERMINAL TIP. 6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY. 7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION. 8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 9. DRAWING CONFORMS TO JEDEC MO220 REVISION C. Maxim cannot assume ...