HCPL4562 HP [Agilent(Hewlett-Packard)], HCPL4562 Datasheet - Page 11

• Manufacturer Part Number: HCPL4562
• Description: High Bandwidth, Analog/Video Optocouplers
• Manufacturer: HP [Agilent(Hewlett-Packard)]

Notes:
Package Characteristics
All Typicals at T
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Related Characteristics Table (if
applicable), your equipment level safety specification or HP Application Note 1074 entitled “Optocoupler Input-Output Endurance
Voltage,” publication number 5963-2203E.
1. When used in the circuit of Figure 1
2. Derate linearly above 70 C free-air
3. Maximum variation from the best fit
4. CURRENT TRANSFER RATIO (CTR)
5. Device considered a two-terminal
6. Flat-band, small-signal voltage gain.
7. The frequency at which the gain is
Input-Output
Momentary
Withstand
Voltage*
Input-Output
Resistance
Input-Output
Capacitance
Parameter
or Figure 4; G
6 mA (HCPL-4562), I
(HCNW4562).
temperature at a rate of 2.0 mW/ C
(HCPL-4562).
line of I
percentage of the peak-to-peak full
scale output.
is defined as the ratio of output
collector current, I
LED input current, I
device: Pins 1, 2, 3, and 4 shorted
together and Pins 5, 6, 7, and 8
shorted together.
3 dB below the flat-band gain.
PB
vs. I
V
F
A
= V
expressed as a
= 25 C
Sym.
O
V
OUT
R
C
, to the forward
F
ISO
FQ
, times 100%.
I-O
I-O
/V
= 10 mA
IN
; I
(Option 020)
FQ
HCNW4562
HCNW4562
HCNW4562
HCPL-4562
HCPL-4562
HCPL-4562
HCPL-4562
=
Device
10. TOTAL HARMONIC DISTORTION
11. ISOLATION MODE REJECTION
8. Differential gain is the change in the
9. Differential phase is the change in the
small-signal gain of the optocoupler
at 3.58 MHz as the bias level is varied
over a given range.
small-signal phase response of the
optocoupler at 3.58 MHz as the bias
level is varied over a given range.
(THD) is defined as the square root
of the sum of the square of each
harmonic distortion component. The
THD of the isolated video circuit is
measured using a 2.6 k
series with the 50
of the spectrum analyzer.
RATIO (IMRR), a measure of the
optocoupler’s ability to reject signals
or noise that may exist between input
and output terminals, is defined by
20 log
2500
5000
5000
Min.
10
10
12
11
10
[(V
Typ.
10
10
OUT
0.6
0.5
12
13
/V
IN
)/(V
input impedance
Max.
OUT
0.6
load in
/V
IM
)],
Units
V rms
pF
12. In accordance with UL 1577, each
13. In accordance with UL 1577, each
Test Conditions
RH
t = 1 min.,
T
V
T
T
f = 1 MHz
A
A
A
I-O
where V
voltage signal.
optocoupler is proof tested by
applying an insulation test voltage
detection current limit, I
This test is performed before the
100% Production test shown in the
VDE 0884 Insulation Related
Characteristics Table, if applicable.
optocoupler is proof tested by
applying an insulation test voltage
detection current limit, I
This test is performed before the
100% Production test shown in the
VDE 0884 Insulation Related
Characteristics Table, if applicable.
= 25 C
= 25 C
= 100 C
3000 V rms for 1 second (leakage
6000 V rms for 1 second (leakage
= 500 Vdc
50%,
IM
is the isolation mode
Fig.
I-O
I-O
5 A).
5 A).
Note
5, 12
5, 13
5, 13
1-395
5
5