LMC7101_05 MICREL [Micrel Semiconductor], LMC7101_05 Datasheet - Page 5

• Manufacturer Part Number: LMC7101_05
• Description: Low-Power Operational Amplifier
• Manufacturer: MICREL [Micrel Semiconductor]

Electrical Characteristics—AC (5V)
V+ = 5V, V– = 0V, V
Symbol
THD
SR
GBW
Electrical Characteristics—AC (12V)
V+ = 12V, V– = 0V, V
Symbol
THD
SR
GBW
φ
G
e
i
General Notes: Devices are ESD protected; however, handling precautions are recommended. All limits guaranteed by testing on statistical analysis.
Note 1.
Note 2.
Note 3.
Note 4.
Note 5.
Note 6.
Note 7.
Note 8.
Note 9.
Note 10. Device connected as a voltage follower with a 12V step input. The value is the positive or negative slew rate, whichever is slower.
February 2005
LMC7101
n
m
n
m
Absolute maximum ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when
operating the device outside its recommended operating ratings.
I/O Pin Voltage is any external voltage to which an input or output is referenced.
The maximum allowable power dissipation is a function of the maximum junction temperature, T
resistance, θ
P
Thermal resistance, θ
Human body model, 1.5k in series with 100pF.
Common-mode performance tends to follow the typical value. Minimum value limits reflect performance only near the supply rails.
Continuous short circuit may exceed absolute maximum T
Shorting OUT to V+ when V+ > 12V may damage the device.
R
D
L
connected to 5.0V. Sourcing: 5V ≤ V
= (T
Parameter
Total Harmonic Distortion
Slew Rate
Gain-Bandwidth Product
Parameter
Total Harmonic Distortion
Slew Rate
Gain-Bandwidth Product
Phase Margin
Gain Margin
Input-Referred Voltage Noise
Input-Referred Current Noise
J(max)
CM
JA
– T
CM
; and the ambient temperature, T
= 1.5V, V
A
= 1.5V, V
) ÷ θ
JA
JA
, applies to a part soldered on a printed-circuit board.
. Exceeding the maximum allowable power dissipation will result in excessive die temperature.
OUT
OUT
= V+/2; R
= V+/2; R
OUT
L
L
≤ 12V. Sinking: 2.5V ≤ V
= 1MΩ; T
= 1MΩ; T
A
. The maximum allowable power dissipation at any ambient temperature is calculated using:
Condition
f = 10kHz, A
R
Condition
f = 10kHz, A
R
V+ = 12V, Note 10
f = 1kHz, V
f = 1kHz
L
L
= 2kΩ, V
= 2k, V
J
J
= 25°C, bold values indicate –40°C ≤ T
J
= 25°C, bold values indicate –40°C ≤ T
under some conditions.
OUT
CM
OUT
V
V
5
= –2,
= –2,
= 1V
= 8.5 V
OUT
= 4.0 V
≤ 5V.
PP
PP
0.01
0.01
Typ
Typ
0.3
0.5
0.3
0.5
1.5
45
10
37
0.19
0.15
Min
Min
J(max)
LMC7101A
LMC7101A
J
; the junction-to-ambient thermal
J
≤ +85°C; unless noted
≤ +85°C; unless noted
Max
Max
0.19
0.15
Min
Min
LMC7101B
LMC7101B
Max
Max
Micrel, Inc.
LMC7101
nV/ Hz
fA/ Hz
Units
Units
V/µs
MHz
V/µs
V/µs
MHz
dB
%
%
°