MM1495XF MITSUMI [Mitsumi Electronics, Corp.], MM1495XF Datasheet
MM1495XF
Available stocks
Related parts for MM1495XF
MM1495XF Summary of contents
Page 1
... Video and audio switches can be controlled independently. 6. 6dB amp built in to video and audio systems. 7. Output voltage gain can be varied by mounting an external resistor on the audio input pin. 8. Slave address can be changed: 90H or 92H 9. Built-in 3-value identification function Package SOP-44A (MM1495XF) SDIP-42A (MM1495XD) Applications Other video equipment 2 ...
Page 2
MITSUMI Block Diagram Y Y S/Comp S/Comp judgment judgment 11. 11. 11. ...
Page 3
... MITSUMI Pin Assignment Typical model: MM1495XF Y I has Address pin. Pin Description Pin No. Pin name ...
Page 4
MITSUMI Pin No. Pin name I/O1 11 I/O2 16 I/O3 20 GND Sync out 22 SCL BUS Control 5-Input 2-Output ...
Page 5
MITSUMI Pin No. Pin name SDA 24 Address 27 CLAMP 25 BIAS OUT OUT OUT OUT OUT OUT ...
Page 6
MITSUMI Pin No. Pin name OUT OUT OUT C 44 OUT BUS Control 5-Input 2-Output AV Switch MM1495X Function Video output ...
Page 7
... C BUS Control 5-Input 2-Output AV Switch MM1495X (Ta=25°C) Symbol T STG T OPR V max Symbol T OPR V OP Typical model: MM1495XF (Except where noted therwise, Ta=25°C, V Symbol Measurement conditions I No signal 10, 13, 15, 19, 32, 34, 36, 38 pin VIN V 30, 40 pin VOUT V 42, 44 pin SOUT V ...
Page 8
MITSUMI Item V 2 OUT Voltage gain Frequency characteristic Differential gain Differential phase Input dynamic range Output impedance Crosstalk Y OUT Voltage gain Frequency characteristic Differential gain Differential phase Input dynamic range Crosstalk C OUT Voltage gain Frequency characteristic Differential ...
Page 9
MITSUMI Item L 2 OUT Voltage gain Frequency characteristic Total harmonic distortion Output offset voltage Output dynamic range Crosstalk Ripple rejection R 2 OUT Voltage gain Frequency characteristic Total harmonic distortion Output offset voltage Output dynamic range Crosstalk Ripple rejection ...
Page 10
MITSUMI Item condition (Note.2) Input voltage L Input voltage H Low level output voltage High level input current Low level input current Clock frequency Data transfer wait time SCL start hold time SCL low level hold time ...
Page 11
... MITSUMI Measuring Circuit 1 V (9V) CC SG3 SG4 SG1 SG2 SG5 SG6 GND BUS Control 5-Input 2-Output AV Switch MM1495X MM1495XF 92H 90H SDA SCL 10k 10k 10k 10k ...
Page 12
... MITSUMI Measuring Circuit 2 For measuring crosstalk V (9V) CC SG1 SG2 SG5 SG6 GND BUS Control 5-Input 2-Output AV Switch MM1495X MM1495XF 92H 90H SDA SCL 10k 10k 10k 10k ...
Page 13
... MITSUMI Measuring Circuit 3 For measuring ripple rejection 0.3V P-P SIN wave DC 9V GND note: Termination of audio input is 2. BUS Control 5-Input 2-Output AV Switch MM1495X MM1495XF 92H 90H SDA SCL 10k 10k 10k 10k ...
Page 14
MITSUMI BUS SDA SCL BUS is inter bus system controled by 2 lines (SDA, SCL). Data are transmitted and received in the units of byte and Acknowledge transmitted ...
Page 15
MITSUMI Switch Control Table Main V select Mode Output Input S Y/V Y Y/V V Y Main L ...
Page 16
MITSUMI Sub V select Mode Output Input S Y/V Y Y/V V Y Sub select Mode ...
Page 17
MITSUMI Sync sepa select Mode Output S2 Y/V S1 Y/V Video V2 V input OUT Video OUT output Y Y OUT Output port switching Mode Port Condition Open I/O1 Low ...
Page 18
MITSUMI { Input port detect: I/O1~3 are identified by 3 values, and output according to the combinations shown in the following table. S detect: Judge the DC level voltage of I/O1~3 DC < = 0.8V 1.4V < ...
Page 19
MITSUMI Application Circuit 2 470k 470k 75 470k 470k 75 470k 75 470k 75 0.01 FS 10k 4.7k 470k 75 470k 75 0.01 FS 10k 4.7k 470k 470k 75 FS 10k 4.7k Port V CC 10k Sync V CC 10k ...