MCP1703-1202E/CD MICROCHIP [Microchip Technology], MCP1703-1202E/CD Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
MCP1703-1202E/CD
Manufacturer Part Number
MCP1703-1202E/CD
Description
250 mA, 16V, Low Quiescent Current
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.MCP1703-1202ECD.pdf
(24 pages)
1.0
Absolute Maximum Ratings †
V
All inputs and outputs w.r.t. .............(V
Peak Output Current ...................................................500 mA
Storage temperature .....................................-65°C to +150°C
Maximum Junction Temperature ................................. +150°C
Operating Junction Temperature...................-40°C to +125°C
ESD protection on all pins (HBM;MM)............... ≥ 4 kV; ≥ 400V
DC CHARACTERISTICS
© 2007 Microchip Technology Inc.
Electrical Specifications: Unless otherwise specified, all limits are established for V
I
Boldface type applies for junction temperatures, T
Input / Output Characteristics
Input Operating Voltage
Input Quiescent Current
Maximum Output Current
Output Short Circuit Current
Output Voltage Regulation
V
Line Regulation
Load Regulation
Note 1:
DD
LOAD
OUT
..................................................................................+18V
Temperature Coefficient
= 100 µA, C
2:
3:
4:
5:
6:
7:
Parameters
ELECTRICAL
CHARACTERISTICS
The minimum V
V
The input voltage V
TCV
ature range. V
Load regulation is measured at a constant junction temperature using low duty cycle pulse testing. Changes in output
voltage due to heating effects are determined using thermal regulation specification TCV
Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its measured
value with an applied input voltage of V
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction to air (i.e., T
dissipation will cause the device operating junction temperature to exceed the maximum 150°C rating. Sustained
junction temperatures above 150°C can impact the device reliability.
The junction temperature is approximated by soaking the device under test at an ambient temperature equal to the
desired Junction temperature. The test time is small enough such that the rise in the Junction temperature over the
ambient temperature is not significant.
R
is the nominal regulator output voltage. For example: V
OUT
OUT
= (V
= 1 µF (X7R), C
OUT-HIGH
OUT-LOW
IN
must meet two conditions: V
IN
(V
Δ
V
= V
OUT
Symbol
I
TCV
I
- V
ΔV
OUT_mA
OUT_SC
OUT
= lowest voltage measured over the temperature range.
V
V
OUT
OUT(MAX)
OUT-LOW
SS
I
OUT
XΔV
IN
q
IN
OUT
/V
-0.3V) to (V
= 1 µF (X7R), T
OUT
/
IN
)
) *10
+ V
V
V
R
R
Min
250
100
150
200
-0.3
-2.5
2.7
-3.0%
-2.0%
J
DROPOUT(MAX)
50
6
—
—
—
OUT(MAX)
IN
(Note 7) of -40°C to +125°C.
/ (V
+0.3V)
R
A
* ΔTemperature), V
= +25°C.
IN
V
±0.1
±1.0
R
Typ
100
130
200
250
400
2.0
+ V
≥ 2.7V and V
—
—
50
%
±0.4
DROPOUT(MAX)
or Vi
V
V
IN
R
R
† Notice: Stresses above those listed under “Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
R
Max
16.0
+0.3
+2.5
150
+3.0%
+2.0%
—
—
—
—
—
—
= 1.2V, 1.5V, 1.8V, 2.5V, 2.8V, 3.0V, 3.3V, 4.0V, or 5.0V.
= 2.7V (whichever is greater); I
5
IN
OUT-HIGH
≥ (V
A
, T
or 2.7V, whichever is greater.
OUT(MAX)
J
ppm/°C
, θ
Units
%/V
mA
mA
mA
mA
mA
mA
µA
JA
IN
%
V
V
= highest voltage measured over the temper-
). Exceeding the maximum allowable power
= V
OUT(MAX)
+ V
Note 1
I
For V
For V
For V
For V
For V
V
Current (average current) measured
10 ms after short is applied.
Note 2
Note 3
(V
≤ 16V, Note 1
I
I
V
L
L
L
DROPOUT(MAX)
IN
IN
= 0 mA
OUT(MAX)
= 1.0 mA to 250 mA for V
= 1.0 mA to 200 mA for V
= V
= 3.65V, Note 4
R
R
R
R
R
+ V
≥ 2.5V
< 2.5V, V
< 2.5V, V
< 2.5V, V
< 2.5V, V
IN(MIN)
OUT
OUT
DROPOUT(MAX)
MCP1703
.
+ V
Conditions
(Note 1), V
= 100 µA.
DROPOUT(MAX)
).
IN
IN
IN
IN
≥ 2.7V
≥ 2.95V
≥ 3.2V
≥ 3.45V
DS22049A-page 3
, Note 1,
OUT
R
R
) ≤ V
>= 2.5V
< 2.5V
= GND,
IN