TK65910MTL/A0 TOKO [TOKO, Inc], TK65910MTL/A0 Datasheet
TK65910MTL/A0
Related parts for TK65910MTL/A0
TK65910MTL/A0 Summary of contents
Page 1
FEATURES High Ratio of Brightness / Input Power Constant Brightness Versus Input Supply Changes Optimized for 3 12.5 nf Panel Capacitance Panel Voltage Slew Rates Controlled for Life Enhancement Panel Peak to Peak Voltage Independent of Input Voltage ...
Page 2
TK6591x ABSOLUTE MAXIMUM RATINGS V Pin .................................................................... 6 All Pins Except V and GND ............................... V CC Power Dissipation (Note 1) ................................ 600 mW TK6591x ELECTRICAL CHARACTERISTICS unless ...
Page 3
TK6591x ELECTRICAL CHARACTERISTICS unless otherwise specified TABLE 1: LAMP FREQUENCY TOKO PART NO. TK65910 TK65911 TK65912 TK65913 TK65914 TK65915 TK65916 TK65917 TK65918 TK65919 TABLE 2: OSCILLATOR FREQUENCY ...
Page 4
TK6591x TYPICAL PERFORMANCE CHARACTERISTICS TK65911 Voltage Waveform Across 5 nF Lamp TK65911 PEAK TO PEAK LAMP VOLTAGE vs. SUPPLY VOLTAGE 150 820 µH 140 130 680 µH 120 110 100 2.5 3 3.5 4 ...
Page 5
TYPICAL PERFORMANCE CHARACTERISTICS (CONT.) TK65911 AVERAGE CONVERTER SUPPLY CURRENT vs. SUPPLY VOLTAGE 2 (V) TK65911 PEAK CURRENT THRESHOLD vs. SUPPLY VOLTAGE ...
Page 6
TK6591x TYPICAL PERFORMANCE CHARACTERISTICS (CONT.) TK65911 PEAK TO PEAK LAMP VOLTAGE vs. TEMPERATURE 140 130 120 110 100 90 -50 - TEMPERATURE ( C) TK65911 LAMP FREQUENCY vs. TEMPERATURE 220 210 200 190 ...
Page 7
TYPICAL PERFORMANCE CHARACTERISTICS (CONT.) TK65911 PEAK CURRENT THRESHOLD vs. TEMPERATURE 2 -50 - TEMPERATURE( C) TK65911 QUIESCENT CURRENT vs. TEMPERATURE 100 ...
Page 8
TK6591x TYPICAL PERFORMANCE CHARACTERISTICS (CONT.) TK65911 MAXIMUM DUTY CYCLE vs. SUPPLY VOLTAGE 2.5 3 3 (V) TK65911 MAXIMUM DUTY CYCLE vs. TEMPERATURE -50 -25 ...
Page 9
An Electroluminescent (EL) Lamp is a strip of plastic, coated with a phosphorous material that emits light when a high voltage AC signal is applied to the terminals of the device. EL panels have the ability to light the entire ...
Page 10
TK6591x THEORY OF OPERATION (CONT.) With properly selected components, the TK6591x will nominally support peak output voltages (180 V ). Should the EL Panel become disconnected PK-PK from the driver outputs, the removal of the load can ...
Page 11
SUPPLY PIN ( This pin is the positive input supply for the TK6591x. Good design practices dictate capacitive decoupling to the ground pin. GROUND PIN (GND) The pin provides the ground connection for the IC. IND PIN This ...
Page 12
TK6591x INDUCTOR VALUE SELECTION Designing an EL Driver utilizing the TK6591x is a very simple task. The primary component affecting the behavior of the converter is the inductor. Essentially, the entire design task primarily consists of selecting the proper inductor ...
Page 13
TK6592x family of EL Drivers which have higher drive capabilities. To utilize the following charts in selecting an appropriate coil, perform the following steps: 1) From the following charts, select the chart that ...
Page 14
TK6591x LOW VOLTAGE SPLIT SUPPLY APPLICATION The split power supply application of this EL driver circuit configuration (see Figure 4) in which the separated or split away from the main power input (V ...
Page 15
APPLICATION INFORMATION (CONT.) TABLE 5: INDUCTANCE SELECTION TABLE FOR SINGLE AND DUAL CELL ALKALINE SYSTEMS PART NO. TK65910 TK65911 f lamp 175 Hz 200 Hz f converter 22.4 kHz 25.6 kHz min.Vp L type D31FU 330 µH 270 µH 0.9V ...
Page 16
TK6591x Page 16 LAYOUT 2x SPLIT SUPPLY LAYOUT 2x Actual Size Actual Size May 2000 TOKO, Inc. ...
Page 17
May 2000 TOKO, Inc. NOTES TK6591x Page 17 ...
Page 18
TK6591x Page 18 NOTES May 2000 TOKO, Inc. ...
Page 19
May 2000 TOKO, Inc. NOTES TK6591x Page 19 ...
Page 20
TK6591x SOT23L-6 +0.15 0.4 - 0.05 0.1 6 Marking +0.15 - 0.05 0. 0.95 0.95 +0.3 - 0.1 3.5 (3.4) Dimensions are shown in millimeters Tolerance: x.x = 0.2 mm (unless otherwise specified) ...