OPT101_03 BURR-BROWN [Burr-Brown Corporation], OPT101_03 Datasheet
OPT101_03
Related parts for OPT101_03
OPT101_03 Summary of contents
Page 1
... The integrated combination of photodiode and transimpedance amplifier on a single chip eliminates the problems commonly encountered in discrete designs such as leakage current errors, noise pick-up, and gain peaking due to stray capacitance. The 0.09 x 0.09 inch photodiode is operated in the photoconductive mode for excellent linearity and low dark current ...
Page 2
... Temperature Unit to Unit Variation (1) Nonlinearity Photodiode Area (2) DARK ERRORS, RTO Offset Voltage, Output vs Temperature vs Power Supply Voltage Noise, Dark 0.1Hz to 20kHz B TRANSIMPEDANCE GAIN Resistor Tolerance Temperature FREQUENCY RESPONSE Bandwidth Rise Fall Time, 10% to 90% Settling Time, 0.05% 0.1% 1% Overload Recovery OUTPUT Voltage Output, High ...
Page 3
OP AMP SPECIFICATIONS + +2.7V to +36V, = 650nm, internal PARAMETER INPUT Offset Voltage vs Temperature vs Power Supply Input Bias Current vs Temperature Input Impedance Differential Common-Mode Common-Mode Input Voltage ...
Page 4
PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE-LEAD OPT101P DIP-8 OPT101P-J DIP-8, Surface Mount (2) NOTES: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this data sheet. (2) 8-pin DIP with J-formed leads for ...
Page 5
TYPICAL PERFORMANCE CURVES + +2.7V to +36V, = 650nm, internal NORMALIZED SPECTRAL RESPONSIVITY 1.0 Ultraviolet 0.9 0.8 0.7 0.6 650nm (0.45A/W) 0.5 0.4 0.3 0.2 0.1 0 200 300 400 500 ...
Page 6
TYPICAL PERFORMANCE CURVES + +2.7V to +36V, = 650nm, internal QUIESCENT CURRENT vs TEMPERATURE 300 275 250 225 200 175 150 125 100 Temperature ...
Page 7
TYPICAL PERFORMANCE CURVES + +2.7V to +36V, = 650nm, internal SMALL SIGNAL RESPONSE SMALL SIGNAL RESPONSE (C LOAD (Pin 3 = 0V) OPT101 SBBS002A (Cont.) feedback resistor, and R = 10k ...
Page 8
APPLICATIONS INFORMATION Figure 1 shows the basic connections required to operate the OPT101. Applications with high-impedance power supplies may require decoupling capacitors located close to the device pins as shown. Output is 7.5mV dc with no light and increases with ...
Page 9
DARK ERRORS The dark errors in the specification table include all sources. The dominant source of dark output voltage is the “pedestal” voltage applied to the non-inverting input of the op amp. This voltage is introduced to provide linear operation ...
Page 10
... An external 1M resistor used in the configuration shown in Figure 4b will create a 23kHz bandwidth with the 6 same 10 V/A dc transimpedance gain. This yields a rise time of approximately 15 s (10% to 90%). Dynamic response is not limited by op amp slew rate. This is demonstrated by the dynamic response oscilloscope photographs showing virtually identical large-signal and small-signal response ...
Page 11
V B OPT101 3pF 1M 8pF V B OPT101 8 3 FIGURE 6. Differential Light Measurement. +15V 10k 2 100k 10V REF102 6 4 11k FIGURE 7. LED Output Regulation Circuit. OPT101 SBBS002A ...
Page 12
PACKAGING INFORMATION ORDERABLE DEVICE STATUS(1) OPT101P ACTIVE OPT101P-J ACTIVE (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period ...
Page 13
NTC (R-PDIP-T8) D 0.390 (9,91) 0.360 (9,14 Index 1 4 Area 5.5 –8.5 0.070 (1,78) H 0.045 (1,14) Base Plane Seating Plane 0.005 (0,13) MIN D 1/2 Lead 4 PL 0.045 (1,143) H 0.030 (0,762 0.022 ...
Page 14
...
Page 15
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the ...