HN58W241000FPIE RENESAS [Renesas Technology Corp], HN58W241000FPIE Datasheet
HN58W241000FPIE
Related parts for HN58W241000FPIE
HN58W241000FPIE Summary of contents
Page 1
... Shipping tape and reel: 1,500 IC/reel • Temperature range: −40 to +85°C • Lead free products. 2 Note trademark of Philips Corporation. Ordering Information Type No. Internal organization HN58W241000FPIE 1M bit (131,072 × 8-bit) Rev.3.00, Jul.12.2005, page serial bus* ) Operating voltage 2 ...
Page 2
HN58W241000I Pin Arrangement Pin Description Pin name A1, A2 SCL SDA Block Diagram A1, A2 SCL SDA Absolute Maximum Ratings Parameter Supply voltage relative Input voltage ...
Page 3
HN58W241000I DC Operating Conditions Parameter Supply voltage Input high voltage Input low voltage Operating temperature (min): −1.0 V for pulse width ≤ 50 ns. Notes 1.0 V for pulse width ≤ (max): ...
Page 4
HN58W241000I (Ta = −40 to +85° Characteristics Test Conditions • Input pules levels: 0.2 × 0.8 × • Input rise and fall time: ≤ ...
Page 5
HN58W241000I Timing Waveforms Bus Timing t F SCL t SU.STA SDA (in) SDA (out) t SU.WP WP Write Cycle Timing SCL D0 in SDA Write data (Address (n)) Rev.3.00, Jul.12.2005, page 1/f SCL t t LOW HIGH ...
Page 6
HN58W241000I Pin Function Serial Clock (SCL) The SCL pin is used to control serial input/output data timing. The SCL input is used to positive edge clock data into EEPROM device and negative edge clock data out of each device. Maximum ...
Page 7
HN58W241000I Device Address (A1, A2 four devices can be addressed on the same bus by setting the levels on these pins to different combinations. The levels on these pins are compared with the device address code which are ...
Page 8
HN58W241000I Functional Description Start Condition A high-to-low transition of the SDA with the SCL high is needed in order to start read, write operation. (See start condition and stop condition) Stop Condition A low-to-high transition of the SDA with the ...
Page 9
HN58W241000I Acknowledge All addresses and data words are serially transmitted to and from in 8-bit words. The receiver sends a zero to acknowledge that it has received each word. This happens during ninth clock cycle. The transmitter keeps bus open ...
Page 10
HN58W241000I Device Addressing The EEPROM device requires an 8-bit device address word following a start condition to enable the chip for a read or a write operation. The device address word consists of 4-bit device code, 3-bit device address code ...
Page 11
HN58W241000I Write Operations Byte Write: A write operation requires an 8-bit device address word with R/W = “0”. Then the EEPROM sends acknowledgment "0" at the ninth clock cycle. After these, the EEPROM receives 2 sequence 8-bit memory address words. ...
Page 12
HN58W241000I Page Write: The EEPROM is capable of the page write operation which allows any number of bytes up to 256 bytes to be written in a single write cycle. The page write is the same sequence as the byte ...
Page 13
HN58W241000I Acknowledge Polling: Acknowledge polling feature is used to show if the EEPROM internally-timed write cycle or not. This feature is initiated by the stop condition after inputting write data. This requires the 8-bit device address word ...
Page 14
HN58W241000I Read Operation There are three read operations: current address read, random read, and sequential read. Read operations are initiated the same way as write operations with the exception of R/W = “1”. Current Address Read: The internal address counter ...
Page 15
HN58W241000I Random Read: This is a read operation with defined read address. A random read requires a dummy write to set read address. The EEPROM receives a start condition, device address word (R/W=0) and memory address 2 × 8-bit sequentially. ...
Page 16
HN58W241000I Sequential Read: Sequential reads are initiated by either a current address read or a random read. If the EEPROM receives acknowledgment “0” after 8-bit read data, the read address is incremented and the next 8-bit read data are coming ...
Page 17
HN58W241000I Notes Data Protection at V On/Off CC When V is turned on or off, noise on the SCL and SDA inputs generated by external circuits (CPU, etc) may act trigger and turn the EEPROM to unintentional ...
Page 18
... HN58W241000I Package Dimensions HN58W241000FPIE (PRSP0008DG-B / Previous Code: JEITA Package Code RENESAS Code P-SOP8-5.3x5.65-1.27 PRSP0008DG Index mark Rev.3.00, Jul.12.2005, page FP-8DFV) Previous Code MASS[Typ.] FP-8DFV 0.153g NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. ...
Page 19
... Jul.12.2005 Contents of Modification Initial issue Change format issued by Renesas Technology Corp. Deletion of Preliminary Ordering Information Addition of HN58W241000FPIE Package Dimensions FP-8DF to FP-8DF, FP-8DFV Ordering Information Deletion of HN58W241000FPI Package Dimensions Deletion of FP-8DF Ordering Information Addition of Renesas package codes AC Characteristics Addition ...
Page 20
Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead ...