ILC7082 Impala Linear Corporation, ILC7082 Datasheet - Page 7

• Manufacturer Part Number: ILC7082
• Description: 150MA SOT-23 ULTRA LOW NOISE CMOS RF-LDO REGULATOR
• Manufacturer: Impala Linear Corporation

Input Capacitor
An input capacitor C
nected from V
filter supply noise from entering the LDO. The input capaci-
tor should be connected as close to the LDO regulator input
pin as is practical. Using a high-value input capacitor will
offer superior line transient response as well as better pow-
er supply ripple rejection. A ceramic or tantalum capacitor
may be used at the input of the LDO regulator.
Note that there is a parasitic diode from the LDO regulator
output to the input. If the input voltage swings below the reg-
ulator’s output voltage by a couple of hundred milivolts then
the regulator may be damaged. This condition must be
avoided. In many applications a large value input capacitor,
C
when the LDO is powered off.
Output Capacitor Selection
Impala strongly recommends the use of low ESR (equiva-
lent series resistance) ceramic capacitors for C
C
as zero ). The value of the output capacitor should be 1 F
or higher. Either ceramic chip or a tantalum capacitor may
be used at the output.
Use of ceramic chip capacitors offer significant advantages
over tantalum capacitors. A ceramic capacitor is typically
cheaper than a tantalum capacitor, it usually has a smaller
footprint, lower height, and lighter weight than a tantalum
capacitor. Furthermore, unlike tantalum capacitors which are
polarized and can be damaged if connected incorrectly,
ceramic capacitors are non-polarized. Low value ceramic
chip capacitors with X5R or X7R dielectric are available in
the 100pF to 4.7mF range. Beware of using ceramic capaci-
tors with Y5V dielectric since their ESR increases significant-
ly at cold temperatures. Figure 12 shows a list of recom-
mended ceramic capacitors for use at the output of ILC7082.
Note: If a tantalum output capacitor is used then for stable
operation Impala recommends a low ESR tantalum capaci-
tor with maximum rated ESR at or below 0.4W. Low ESR
tantalum capacitors, such as the TPS series from AVX
Corporation (www.avxcorp.com) or the T495 series from
Kemet (www.kemet.com) may be used.
In applications where a high output surge current can be expect-
ed, use a high value but low ESR output capacitor for superior
load transient response. The ILC7082 is stable with no load.
Noise Bypass Capacitor
In low noise applications, the self noise of the ILC7082 can
be decreased further by connecting a capacitor from the
noise bypass pin (pin 4) to ground (pin 2). The noise bypass
pin is a high impedance node as such care should be taken
in printed circuit board layout to avoid noise pick-up from
external sources. Moreover, the noise bypass capacitor
should have low leakage.
ILC7082 1.3
IN
NOISE
150mA SOT-23 Ultra Low Noise CMOS RF-LDO™ Regulator
, will hold V
Impala Linear Corporation
The ILC7082 is stable with low ESR capacitor (as low
IN
IN
to the main ground plane. This will help to
higher than V
IN
of value 1 F or larger should be con-
OUT
and decay slower than V
[phone]
OUT
and
OUT
Noise bypass capacitors with a value as low as 470pF may
be used. However, for optimum performance, use a 0.01mF
or larger, ceramic chip capacitor. Note that the turn on and
turn off response of the ILC7082 is inversely proportional to
the value of the noise bypass capacitor. For fast turn on and
turn off, use a small value noise bypass capacitor. In appli-
cations were exceptionally low output noise is not required,
consider omitting the noise bypass capacitor altogether.
The Effects of ESR (Equivalent Series Resistance)
The ESR of a capacitor is a measure of the resistance due
to the leads and the internal connections of the component.
Typically measured in m
ohms in some cases.
Wherever there is a combination of resistance and current,
voltages will be present. The control functions of LDOs use
two voltages in order to maintain the output precisely; V
and V
With reference to the block diagram in figure 4, V
back to the error amplifier and is used as the supply voltage
for the internal components of the ILC7082. So any change
in V
maintain V
reflected into the supply of each internal components of the
ILC7082. So any change in V
fier to try to compensate to maintain V
noise on V
nal circuit. The reference voltage, V
C
age and be fed through the circuit. These factors will not
cause a problem if some simple steps are taken. Figure 5
shows where these added ESR resistances are present in
the typical LDO circuit.
With this in mind low ESR components will offer better per-
formance where the LDO may be subjected to large load
transients current. ESR is less of a problem with C
voltage fluctuations at the input will be filtered by the LDO.
www.impalalinear.com
NOISE
OUT
REF
pin. Noise into this pin will add to the reference volt-
will cause the error amplifier to try to compensate to
.
V
Figure 5: ESR present in C
OUT
OUT
OUT
C
will be reflected into the supply of each inter-
V
at the set level and noise on V
I
OUT
I
IN
OUT
C
C
IN
R
C
R*
5
1
SOT-23-5
ILC7082
RF LDO
Regulator
(milli-ohms) it can increase to
OUT
2
TM
will cause the error ampli-
OUT
4
3
REF
and C
ON
OUT
, is influenced by the
at the set level and
OFF
April 1999
R*
C
NOISE
NOISE
OUT
OUT
IN
will be
as the
is fed
7
OUT