A29002 AMIC Technology, A29002 Datasheet - Page 5
![no-image](/images/no-image-200.jpg)
A29002
Manufacturer Part Number
A29002
Description
256K X 8 Bit CMOS 5.0 Volt-only/ Boot Sector Flash Memory
Manufacturer
AMIC Technology
Datasheet
1.A29002.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
A290021T-70
Manufacturer:
AMIC
Quantity:
4 300
Company:
Part Number:
A290021T-70
Manufacturer:
AMIC
Quantity:
4 300
Company:
Part Number:
A290021T-70
Manufacturer:
HIT
Quantity:
6 100
Part Number:
A290021T-70
Manufacturer:
AMIC
Quantity:
20 000
Company:
Part Number:
A290021TL-70
Manufacturer:
SIS
Quantity:
58
Part Number:
A290021TL-70
Manufacturer:
AMIC
Quantity:
20 000
Company:
Part Number:
A290021TL-70F
Manufacturer:
AMIC
Quantity:
126
Part Number:
A290021TL-70F
Manufacturer:
AMIC
Quantity:
20 000
Part Number:
A290021UV-70
Manufacturer:
AMIC
Quantity:
20 000
Part Number:
A29002TL-70
Manufacturer:
AMIC
Quantity:
20 000
Requirements for Reading Array Data
To read array data from the outputs, the system must drive
the
selects the device.
array data to the output pins.
the time during read operation. The internal state machine
is set for reading array data upon device power-up, or after
a hardware reset. This ensures that no spurious alteration
of the memory content occurs during the power transition.
No command is necessary in this mode to obtain array
data. Standard microprocessor read cycles that assert valid
addresses on the device address inputs produce valid data
on the device data outputs. The device remains enabled for
read access until the command register contents are
altered.
See "Reading Array Data" for more information. Refer to the
AC Read Operations table for timing specifications and to
the Read Operations Timings diagram for the timing
waveforms, l
the active current specification for reading array data.
Writing Commands/Command Sequences
To write a command or command sequence (which
includes programming data to the device and erasing
sectors of memory), the system must drive
V
sector, multiple sectors, or the entire device. The Sector
Address Tables indicate the address range that each sector
occupies. A "sector address" consists of the address inputs
required to uniquely select a sector. See the "Command
Definitions" section for details on erasing a sector or the
entire chip, or suspending/resuming the erase operation.
After the system writes the autoselect command sequence,
the device enters the autoselect mode. The system can
then read autoselect codes from the internal register (which
is separate from the memory array) on I/O
read cycle timings apply in this mode. Refer to the
"Autoselect Mode" and "Autoselect Command Sequence"
sections for more information.
I
current specification for the write mode. The "AC
Characteristics" section contains timing specification tables
and timing diagrams for write operations.
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status bits
on I/O
specifications apply. Refer to "Write Operation Status" for
more information, and to each AC Characteristics section
for timing diagrams.
(February, 2002, Version 1.0)
CC2
IL
, and
CE
in the Characteristics table represents the active
7
and
- I/O
OE
OE
CC1
0
. Standard read cycle timings and I
to V
in the DC Characteristics table represents
pins to V
IH
. An erase operation can erase one
OE
is the output control and gates
IL
.
CE
WE
is the power control and
should remain at V
7
WE
- I/O
0
and
. Standard
CC
CE
IH
read
all
to
5
Standby Mode
When the system is not reading or writing to the device, it
can place the device in the standby mode. In this mode,
current consumption is greatly reduced, and the outputs are
placed in the high impedance state, independent of the
input.
The device enters the CMOS standby mode when the
& RESET pins (
than V
A290021) is held at VCC 0.5V. The device requires the
standard access time (t
If the device is deselected during erasure or programming,
the device draws active current until the operation is
completed.
I
current specification.
Output Disable Mode
When the
disabled. The output pins are placed in the high impedance
state.
The RESET pin provides a hardware method of resetting
the device to reading array data. When the system drives
the RESET pin low for at least a period of t
immediately terminates any operation in progress, tristates
all data output pins, and ignores all read/write attempts for
the duration of the RESET pulse. The device also resets
the internal state machine to reading array data. The
operation that was interrupted should be reinitiated once
the device is ready to accept another command sequence,
to ensure data integrity.
The RESET pin may be tied to the system reset circuitry. A
system reset would thus also reset the Flash memory,
enabling the system to read the boot-up firmware from the
Flash memory.
Refer to the AC Characteristics tables for RESET
parameters and diagram.
CE
RESET
CC3
0.5V. (Note that this is a more restricted voltage range
in the DC Characteristics tables represents the standby
is held at V
IH
.) The device enters the TTL standby mode when
: Hardware Reset Pin (N/A on A290021)
OE
input is at V
CE
IH
A29002/A290021 Series
only on A290021) are both held at V
, while RESET (Not available on
CE
) before it is ready to read data.
AMIC Technology, Inc.
IH
, output from the device is
RP
, the device
OE
CE
CC