UCN5801 Allegro, UCN5801 Datasheet
UCN5801
Available stocks
Related parts for UCN5801
UCN5801 Summary of contents
Page 1
... Outputs may be paralleled for higher load current capability. The UCN5800A is furnished in a standard 14-pin DIP; the UCN5800L and UCN5801LW in surface-mountable SOICs; the + 0.3 V UCN5801A in a 22-pin DIP with 0.400" (10.16 mm) row centers; the UCN5801EP in a 28-lead PLCC. FEATURES To 4.4 MHz Data Input Rate High-Voltage, ...
Page 2
... V DD 2.0 1.5 1.0 0.5 14-LEAD SOIC AMBIENT TEMPERATURE IN C 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright © 1985, 1997, Allegro MicroSystems, Inc. COMMON OUT N GROUND TYPICAL BIPOLAR DRIVE Dwg. FP-016-1 22-PIN DIP C/W JA 28-LEAD PLCC C/W JA 14-PIN DIP, R ...
Page 3
... V = 5.0 V, Outputs Open, Inputs = + + 350 UCN5801EP (additional pinout diagrams are on next page (unless otherwise noted). Min. Typ. — — — — — 0.9 — 1.1 — 1.3 — — 10.5 — 8.5 — ...
Page 4
... STROBE GROUND 11 UCN5801LW 1 24 CLEAR STROBE ...
Page 5
AND BiMOS II LATCHED DRIVERS OUTPUT ENABLE (ACTIVE LOW) CLEAR STROBE UNIPOLAR WAVE DRIVE STROBE OUT 1 OUT 2 OUT 3 OUT ...
Page 6
AND BiMOS II LATCHED DRIVERS 14 0.280 0.240 1 0.070 0.045 0.210 MAX 0.015 MIN 0.022 0.014 14 7.11 6.10 1 1.77 1.15 5.33 MAX 0.39 MIN 0.558 0.356 NOTES: 1. Exact body and lead configuration at vendor’s ...
Page 7
AND BiMOS II LATCHED DRIVERS 14 0.1574 0.1497 0.020 1 2 0.013 0.0688 0.0532 0.0040 14 4.00 3.80 0.51 1 0.33 1.75 1.35 0.10 NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. ...
Page 8
... MAX 0.39 MIN 0.558 0.356 NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Lead thickness is measured at seating plane or below. UCN5801A Dimensions in Inches (controlling dimensions 0.100 0.005 BSC MIN 1.120 1.050 ...
Page 9
... BSC 0.219 0.191 0.331 0.533 5.56 4.85 1.27 BSC 5.56 4.85 NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. UCN5801EP Dimensions in Inches (controlling dimensions 0.026 0.032 0.456 0.450 0.495 0.485 25 26 0.020 MIN 0.165 ...
Page 10
... NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. UCN5801LW Dimensions in Inches (for reference only 0.050 3 BSC 0.6141 0.5985 MIN. Dimensions in Millimeters (controlling dimensions 1.27 3 BSC 15.60 15.20 MIN ...
Page 11
AND BiMOS II LATCHED DRIVERS This page intentionally left blank ...
Page 12
... V‡ 450 Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the design of its products. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...