TG161600FFEBB_T1 DATA_IMAGE, TG161600FFEBB_T1 Datasheet - Page 14

• Manufacturer Part Number: TG161600FFEBB_T1
• Description: Single TAB/COG Graphic Module
• Manufacturer: DATA_IMAGE

Confidential Document
8.
8.4 Repetition of High and Low Temperature
8.3 Temperature and Humidity Test:
7.3 Impact Resistance:
7.4 Flexible Pattern Heat Seal Peeling Strength :1.5N/cm (peeling upward by
7.5 Flexible Pattern Bending Resistance Bending: 3 times or more by bending
7.6 Flexible Pattern insert/pull out Resistance 5 times at least.
7.7 Vibration Resistance (In operation)
7.8 Package Drop
8.1 High Temperature Test
8.2 Low Temperature Test
Reliability
•
•
•
•
•
•
•
•
•
•
•
•
•
Linearity :
Insulation Resistance:
Resistance Between Leads :
Operating Fore :
• Resistance Between Leads
•
•
• Operating Fore :
The requirements in 5.1 shall be satisfied.
No faulty operation when sweep vibration of 0.2G 10~55Hz
(1min.) is given for 30min. each in the directions of X,Y,Z.
(Not in operation )
The requirements in 6.2 and 5.1~5.4 shall be satisfied after
sweep vibration of 2g 10~55Hz (1min.) is given for 30min.
each in the directions of X,Y,Z.
After putting panels at the condition of -40°C for 30minutes,and then 80°C for 30 minutes and
this process is repeated by 10 cycles, then leaving for 24 hours at room temperature.
Operating Fore
• Insulation Resistance:
Linearity :
Operating Fore:
Linearity :
Insulation Resistance:
Resistance Between Leads :
Insulation Resistance:
After putting panels at-40°C for 120 hours, then leaving for 24 hours at room temperature.
Resistance Between Leads : FILM (X axis)
then leaving for 24 hours at room temperature
After putting Panels at 80°C for 120 hours, then leaving for 24 hours at room temperature.
Linearity :
Insulation Resistance:
No damage when φ9mm steel ball is dropped on the surface from 30cm height
at 1 time.
90deg. Speed:50mm/min)
radius R1.0mm.
No damage to the product.(1 corner edge, 2 ridges, 4 surfaces, drop from 50
cm height:65cm for the bottom)
X axis ±1.5%↓, Y axis ±1.5%↓
X axis ±1.5%↓, Y axis ±1.5%↓
X axis ±1.5%↓, Y axis ±1.5%↓
X axis ±1.5%↓, Y axis ±1.5%↓
:
80g↓ With R8.0 HS40° Silicon Rubber
80g↓ With R0.8 Polyacetal pen
80g↓ With R0.8 Polyacetal pen
80g↓ With R8.0 HS40° Silicon Rubber
80g↓ With R8.0 HS40° Silicon Rubber
80g↓ With R8.0 HS40° Silicon Rubber
20MΩ↑
20MΩ↑
20MΩ↑
20MΩ↑
FILM (X axis)
20MΩ↑
: FILM (X axis)
FILM (X axis)
After putting panels at 60°C, 90%RH for 120 hours,
@DC 25V
@DC 25V
@DC 25V
80g↓ With R0.8 Polyacetal pen
80g↓ With R0.8 Polyacetal pen
@DC 25V
@DC 25V
GLASS(Y axis)
GLASS(Y axis)
GLASS(Y axis)
GLASS(Y axis)
Page:
14 /22