SP791CN SIPEX [Sipex Corporation], SP791CN Datasheet
SP791CN
Available stocks
Related parts for SP791CN
SP791CN Summary of contents
Page 1
Low Power Microprocessor Supervisory Precision 4.65V Voltage Monitoring 200ms Power-OK/Reset Time Delay Independent Watchdog Time-Preset or Adjustable 75 A Maximum Operating Supply Current 1.0 A Maximum Battery Backup Current 0.1 A Maximum Battery Standby Current Power Switching 250mA Output ...
Page 2
ABSOLUTE MAXIMUM RATINGS Input Voltage (with respect to GND) VCC..................................................-0.3V to +6V VBATT.................................. ............-0.3V to +6V All Other Inputs ................-0.3V to (VOUT + 0.3V) Input Current VCC Peak..................................................... 1.0A VCC Continuous .......................................250mA VBATT Peak ..............................................250mA VBATT Continuous.......................................25mA GND, BATT ON ...
Page 3
ELECTRICAL CHARACTERISTICS (continued) (Vcc = 4.75V to 5.5V 2.8V BATT A MIN PARAMETER MIN BATT ON Output Low Voltage BATT ON Output Short Circuit Current RESET, LOW-LINE AND WATCHDOG TIMER RESET Threshold Voltage ...
Page 4
ELECTRICAL CHARACTERISTICS (continued) (Vcc = 4.75V to 5.5V 2.8V BATT A MIN PARAMETER MIN WDI Threshold Voltage 0. (Note 4) WDI Input Current POWER FAIL COMPARATOR PFI Input Threshold PFI Leakage ...
Page 5
PINOUT TOP VIEW BATT OUT Vcc 3 14 GND 4 13 Corporation BATT PFO 11 PFI 7 10 SWT 8 9 DIP/SO PIN ASSIGNMENTS Pin 1 — V — Backup-Battery ...
Page 6
TYPICAL CHARACTERISTICS V Supply Current vs. CC Temperature (Normal Mode = =2.8V 53 BATT -60 - 120 150 Temperature Deg ...
Page 7
TYPICAL CHARACTERISTICS Maximum Reset Comparator Overdrive Without Causing a Reset 100 0.1 F Capacitor V OUT 80 Above Line 60 Reset Generated 40 Below Line No Reset Generated 100 1000 Reset Threshold Voltage - V CC Chip-Enable ...
Page 8
F OTHER SYSTEM RESET SOURCES UNREGULATED SUPPLY UNREGULATED SUPPLY FAILURE Typical Operating Circuit MR RESET OUT Figure 2. Manual-Reset Timing Diagram FEATURES The SP791 is a microprocessor ( P) supervi- sory circuit that monitors ...
Page 9
RESET 10k Corporation Figure 4. Adding an external pull-down resistor ensures RESET is valid with V down to GND +5V REACTIVATE Figure 6. Two consecutive watchdog faults latch the system in reset. MR low ...
Page 10
WATCHDOG FUNCTION The watchdog monitors P activity via the Watchdog Input (WDI). If the P becomes in- active over a period of time, WDO and WDPO are asserted. To use the watchdog functon, connect WDI to a bus line or ...
Page 11
Vcc RESET THRESHOLD OUT RESET Figure 7. Reset and Chip-Enable Timing The 10ns maximum CE propagation from enables the SP791 to be used with IN OUT most Ps. CHIP-ENABLE INPUT CE is high impedance ...
Page 12
FROM REGULATED SUPPLY VOLTAGE UNREGULATED REGULATOR SUPPLY b.) Figure the unregulated supply is inaccessible, LOWLINE generates the NMI for the P. b) Use PFO to generate the P NMI if the unregulated supply is accessible. LOWLINE OUTPUT ...
Page 13
INPUT/OUTPUT STATES IN BATTERY-BACKUP MODE PIN NAME STATUS 1 V Supply current maximum BATT When V < BATT connected to V OUT OUT through an Internal PMOS switch Battery-switchover ...
Page 14
RESET THRESHOLD 200ms TYP Vcc RESET OUT SECOND CE PULSE ABSENT WHEN V Figure 11. Backup-Battery Monitor Timing Diagram LOW-BATTERY MONITOR The SP791 low-battery voltage function moni- tors V . Low-battery detection of 2.0V BATT 0.15V is ...
Page 15
Rp V OUT CE CE OUT IN Corporation GND * MAXIMUM Rp VALUE DEPENDS ON ACTIVE-HIGH CE THE NUMBER OF RAM DEVICES. MINIMUM Rp VALUE IS 1K LINES FROM LOGIC Figure 13. Alternate CE Gating Leakage current through the ...
Page 16
R1 Vcc PFI Corporation R2 GND V– +5V PFO 0V V TRIP 5 - 1.25 1. TRIP = R1 R2 NOTE NEGATIVE. TRIP Figure 15. Monitoring a Negative Voltage NEGATIVE-GOING V TRANSIENTS CC The SP791 ...
Page 17
D1 = 0.005" min. (0.127 min 0.100 BSC (2.540 BSC) ALTERNATE END PINS (BOTH ENDS) DIMENSIONS (Inches) 8–PIN Minimum/Maximum (mm) 0.115/0.195 A2 (2.921/4.953) B 0.014/0.022 (0.356/0.559) 0.045/0.070 B1 (1.143/1.778) C 0.008/0.014 (0.203/0.356) 0.355/0.400 D (9.017/10.160) E 0.300/0.325 ...
Page 18
DIMENSIONS (Inches) Minimum/Maximum 8–PIN (mm) A 0.053/0.069 (1.346/1.748) A1 0.004/0.010 (0.102/0.249 B 0.014/0.019 (0.35/0.49) D 0.189/0.197 (4.80/5.00) E 0.150/0.157 (3.802/3.988) e 0.050 BSC (1.270 BSC) H 0.228/0.244 (5.801/6.198) h 0.010/0.020 (0.254/0.498) L 0.016/0.050 (0.406/1.270) ...
Page 19
... Model SP791CP ................................................................................... 0˚C to +70˚C .............................................................................. 16-pin, Plastic DIP SP791CN ................................................................................... 0˚C to +70˚C .......................................................................... 16-pin, Narrow SOIC SP791EP .................................................................................... -40˚C to +85˚C .......................................................................... 16–pin, Plastic Dip SP791EN ................................................................................... -40˚C to +85˚C ..................................................................... 16–pin, Narrow SOIC Please consult the factory for pricing and availability on a Tape-On-Reel option. ...