HDSP-5301 Agilent(Hewlett-Packard), HDSP-5301 Datasheet - Page 9

• Manufacturer Part Number: HDSP-5301
• Description: 14.2 mm (0.56 inch) Seven Segment Displays
• Manufacturer: Agilent(Hewlett-Packard)

HDMP-1636/46 (TRx)
Thermal and Power Temperature Characteristics
T
Notes:
1. P
2. Typical value specified with V
3. Specified with high speed outputs biased with 150
4. Based on independent package testing by HP.
HDMP-1636/46 (Transmitter Section)
Output Jitter Characteristics
T
Note:
1. Defined by Fibre Channel Specification X3.230-1994 FC-PH Standard, Annex A, Section A.4 and tested using measurement method
Figure 8. Transmitter Jitter Measurement Method.
a. Block Diagram of RJ Measurement Method.
1.25 GHz
* PATTERN
GENERATOR
PROVIDES A
DIVIDE BY
10 FUNCTION.
A
P
A
CLOCK SOURCE
bias resistors.
HDMP-1646.
in a given application, use the value as described as follows: T
the top center of the package and P
P
Symbol
shown in Figure 8.
GENERATOR*
D,TRx [1,2,3]
= 0 C to +70 C, V
D
= 0 C to +70 C, V
Symbol
D,TRx
DJ
0000011111
RJ
HP70841B
HP70311A
PATTERN
is obtained by multiplying the max V
[1]
jc [4]
[1]
[1,2]
+ DATA
- DATA
ja
Random Jitter at DOUT, the High Speed Electrical Data Port, specified as
1 sigma deviation of the 50% crossing point (RMS)
Deterministic Jitter at DOUT, the High Speed Electrical Data Port (pk-pk)
is measured on a standard 3x3" FR4 PCB in a still air environment. To determine the actual junction temperature
125 MHz
Transceiver Power Dissipation, Outputs Open, Parallel Data
has 5 Ones and 5 Zeroes
Transceiver Power Dissipation, Outputs Connected per
Recommended Bias Terminations with Idle Pattern
Thermal Resistance, Junction to Case
BIAS
TEE
1.4 V
CC
CC
= 3.15 V to 3.45 V
= 3.15 V to 3.45 V
CC
REFCLK LOOPEN
TRIGGER
OSCILLOSCOPE
+DOUT
(STATIC K28.7)
CH1
= 3.3 volts, maximum value specified with V
HDMP-1636
0011111000
HP83480A
Tx[0..9]
D
is the power being dissipated.
-DOUT
CC
CH2
by the max I
ja
Parameter
for these devices is 48 C/Watt for the HDMP-1636 and 44 C/Watt for the
resistors and receiver TTL outputs driving 10 pF loads.
Parameter
CC
and subtracting the power dissipated outside the chip at the high speed
j
= T
VARIABLE
C
OUTPUT)
CIRCUIT
DELAY
DIVIDE
(DUAL
b. Block Diagram of DJ Measurement Method.
BY 10
HDMP-1636
+ (
HDMP-1646
TTL
jc
x Pd), where T
CC
CLOCK SOURCE
= 3.45 volts.
HP70311A
125 MHz
1.25 GHz
CIRCUIT
DIVIDE
BY 2
C
is the case temperature measured on
Units
C/Watt
mW
mW
REFCLK
+DOUT
Tx[0..9]
TRIGGER
OSCILLOSCOPE
+K28.5, -K28.5
GENERATOR
HDMP-1636
CH1
HP70841B
HP83480A
PATTERN
Typ.
Units
630
685
-DOUT
10
ENBYTSYNC
7
ps
ps
+ DATA
Rx[0..9]
- DATA
CH2
LOOPEN
+DIN
-DIN
Max.
850
900
Typ.
15
8
719