HMMC-3102-BLK HP [Agilent(Hewlett-Packard)], HMMC-3102-BLK Datasheet - Page 3

• Manufacturer Part Number: HMMC-3102-BLK
• Description: DC - 16 GHz Packaged Divide-by-2 Prescaler
• Manufacturer: HP [Agilent(Hewlett-Packard)]

RF Specifi cations
(T
Symbol
P
|V
P
P
H
Notes
3. Fundamental of output square wave’s Fourier Series.
4. Square wave amplitude calculated from P out .
Applications
The HMMC-3102 is designed for use in
high frequency communications, micro-
wave instrumentation, and EW radar
systems where low phase-noise PLL
control circuitry or broad-band frequency
translation is required.
Operation
The device is designed to operate
when driven with either a single-ended
or differential sinusoidal input signal
over a 200 MHz to 16 GHz bandwidth.
Below 200 MHz the prescaler input is
“slew-rate” limited, requiring fast
rising and falling edge speeds to
properly divide. The device will operate
at frequencies down to dc when driven
with a square-wave.
out
Spitback
feedthru
2
A
out(p–p)
= 25°C, Z
3
|
4
0
= 50 Ω, V
Parameters/Conditions
@ ƒ
@ ƒ
@ ƒ
@ ƒ
@ ƒ
@ ƒ
ƒ
(@ ƒ
ƒ
(@ ƒ
Power level of ƒ
(@ ƒ
Second harmonic distortion output level
(@ ƒ
out
out
CC
(Continued)
out
out
out
out
out
out
in
in
in
out
power level appearing at RF
power level appearing at RF
– V
= 12 GHz, both RF
= 10 GHz, P
12 GHz, unused RF
< 1 GHz
= 2.5 GHz
= 3.5 GHz
< 1 GHz
= 2.5 GHz
= 3.5 GHz
= 3.0 GHz, referred to P
EE
= 5.0 volts)
in
in
appearing at RF
= 0 dBm, referred to P
Due to the presence of an off-chip
RF-bypass capacitor inside the package
(connected to the V
device), and the unique design of the
device itself, the component may be
biased from either a single positive or
single negative supply bias. The back-
side of the package is not dc
connected to any dc bias point on
the device.
For positive supply operation, V
are nominally biased at any voltage in
the +4.5 to +6.5 volt range with pin 8
(V
eration V
and a negative voltage between
-4.5 to -6.5 volts is applied to
pin 8 (V
out
out
EE
& RF
or RF
) grounded. For negative bias op-
out
in
in
out
EE
out
out
CC
or RF
or RF
(ƒ
).
terminated)
out
or RF
pins are typically grounded
unterminated)
in
in
))
in
out
(ƒ
3
CC
in
))
contact on the
CC
Min.
4
3.5
0
pins
ac-Coupling and dc-Blocking
All RF ports are dc connected on-chip
to the V
Ω resistors. Under any bias condi-
tions where V
the RF ports should be ac coupled via
series capacitors mounted on the PC-
board at each RF port. Only under bias
conditions where V
(as is typical for negative bias supply
operation) may the RF ports be direct
coupled to adjacent circuitry or in
some cases, such as level shifting
to subsequent stages. In the latter
case the package heat sink may be
“fl oated” and bias applied as the dif-
ference between V
Typ.
6
5,5
2.0
0.99
0.94
0.63
-40
-47
-23
-25
CC
contact through on-chip 50
CC
Max.
is not dc grounded
CC
CC
and V
is dc grounded
EE
Units
dBm
dBm
dBm
volts
volts
volts
dBm
dBm
dBc
dBc
.