AK4120VF AKM [Asahi Kasei Microsystems], AK4120VF Datasheet
AK4120VF
Available stocks
Related parts for AK4120VF
AK4120VF Summary of contents
Page 1
Sample Rate Converter with Mixer and Volume The AK4120 is a stereo asynchronous sample rate converter. The input sample rate range is from 8kHz to 48kHz. The output sample rate is fixed at 32kHz, 44.1kHz, 48kHz or 96kHz. AK4120 includes ...
Page 2
... Ordering Guide AK4120VF -40 +85 C AKD4120 n Pin Layout IMCLK1 1 SDTI1 2 IBICK1 3 ILRCK1 4 TEST 5 I2S 6 I2C 7 CAD0 8 CSN/CAD1 9 CCLK/SCL 10 CDTI/SDA 11 PDN 12 MS0134-E-00 24pin VSOP (0.65mm pitch) Evaluation Board for AK4120 Top View IMCLK2 SDTI2 IBICK2 ILRCK2 I2MODE ...
Page 3
ASAHI KASEI No. Pin Name I/O 1 IMCLK1 I 2 SDTI1 I 3 IBICK1 I 4 ILRCK1 I 5 TEST I2S 7 I2C I 8 CAD0 I CSN I 9 CAD1 I CCLK I 10 SCL I ...
Page 4
Note 1) Parameter Power Supplies Input Current, Any Pin Except Supplies Input Voltage Ambient Temperature (Power applied) Storage Temperature Note 1: All voltages with respect to ground. WARNING: Operation at or beyond these limits may result in permanent damage ...
Page 5
ASAHI KASEI -101 -103 -105 -107 -109 -111 -113 -115 32 Figure 1: Input Sample Rate (FSI) vs. THD+N (FSO=48kHz) -80 -85 -90 -95 -100 -105 -110 -115 -120 10 Figure 2: Input Frequency vs. THD+N (FSI=44.1kHz, FSO=48kHz) MS0134-E-00 37 ...
Page 6
ASAHI KASEI (Ta=- VDD=2.7 3.6V; FSO=FSI=fs) Parameter Digital Filter Passband (Note 8) -0.001dB Stopband (Note 8) Passband Ripple Stopband Attenuation Group Delay Note 8. The passband and stopband frequencies scale with fs (system sampling rate). Note 9. This ...
Page 7
ASAHI KASEI (Ta=- VDD=2.7~3.6V; C =20pF) L Parameter Master Clock Input (IMCLK1) Frequency Duty Cycle (at FSI > 33kHz) Duty Cycle (at FSI 33kHz) Master Clock Input (IMCLK2) Frequency Duty Cycle (at FSI > 33kHz) Duty Cycle (at ...
Page 8
ASAHI KASEI Parameter Audio Interface Timing Input#2(Master Mode) at Path Mode 1 BICK Frequency BICK Duty BICK “ ” to LRCK BICK “ ” to SDTO SDTI2 Hold Time from BICK “ ” SDTI2 Setup Time to BICK “ ” ...
Page 9
ASAHI KASEI Parameter Control Interface Timing (3-wire Serial mode): CCLK Period CCLK Pulse Width Low Pulse Width High CDTI Setup Time CDTI Hold Time CSN “H” Time CSN “ ” to CCLK “ ” CCLK “ ” to CSN “ ...
Page 10
ASAHI KASEI n Timing Diagram MCLK tCLKH LRCK BICK tBCKH LRCK tBLR BICK tLRS SDTO SDTI Note: MCLK means IMCLK1, IMCLK2 and OCLK. BICK means IBICK1,IBICK2 and OBICK. LRCK means ILRCK1,ILRCK2 and OLRCK. SDTI means SDTI1 and SDTI2. MS0134-E-00 1/fCLK ...
Page 11
LRCK tMBLR BICK SDTO SDTI CSN tCSS CCLK CDTI WRITE Command Input Timing (3-wire Serial mode) CSN CCLK CDTI D3 WRITE Data Input Timing (3-wire Serial mode) MS0134-E-00 dBCK tSDS tSDH Audio Interface Timing at Master Mode tCCKL tCCKH tCDS ...
Page 12
SDA tBUF tLOW tR SCL tHD:STA tHD:DAT Stop Start tPD PDN SDTO MS0134-E-00 tHIGH tF tSU:DAT tSU:STA Start Bus mode Timing tPDV Power-down & Reset Timing - 12 - VIH VIL tSP VIH VIL tSU:STO Stop VIH ...
Page 13
ASAHI KASEI n I/O Data flow The AK4120 has two input audio data interfaces (Input#1 and Input#2). The AK4120 has four modes of operation, each corresponding to a different internal audio path as shown in Table 1. These path modes ...
Page 14
SDTI1 Input#1 Audio ILRCK1 I/F IBICK1 IMCLK1 IMCLK2 SDTI2 Input#2 Audio ILRCK2 I/F IBICK2 I2MODE CAD0 Figure 3. Path Mode 0 (Input#1 SRC + Mixer) SDTI1 ILRCK1 IBICK1 IMCLK1 IMCLK2 SDTI2 Input#2 Audio ILRCK2 I/F IBICK2 I2MODE CAD0 MS0134-E-00 I2S ...
Page 15
ASAHI KASEI SDTI1 Input#1 Audio ILRCK1 I/F IBICK1 IMCLK1 IMCLK2 SDTI2 Input#2 Audio ILRCK2 I/F IBICK2 I2MODE CAD0 Figure 5. Path Mode 2 (Input#1 through output) SDTI1 ILRCK1 IBICK1 IMCLK1 IMCLK2 SDTI2 Input#2 Audio ILRCK2 I/F IBICK2 I2MODE CAD0 Figure ...
Page 16
ASAHI KASEI n System Clock The external clocks required to operate the AK4120 in each mode are shown in Table 3 and Table 4. The Input#1 port works in slave mode only. The Input#2 and Output ports have both slave ...
Page 17
ASAHI KASEI The frequency of IMCLK1, IMCLK2, and OMCLK are fixed based on the sampling rate and clock speed (256fs/512fs). IMCKS1, IMCKS2 and OMCKS bits in register 01H select clock speed. LRCK fs 32.0kHz 44.1kHz 48.0kHz 88.2kHz 96kHz n Volume ...
Page 18
ASAHI KASEI n Audio Serial Interface Format Four serial data modes can be selected by the I2S pin and D5-D0 bits in register 00H as shown in Table all modes the serial audio data is MSB-first, 2’s ...
Page 19
ASAHI KASEI LRCK BICK (64fs) SDTI Don’t care 16bit 15:MSB, 0:LSB SDTI 19 Don’t care 18 20bit 19:MSB, 0:LSB Lch Data LRCK BICK (64fs) SDTI 20:MSB, 0:LSB Lch Data ...
Page 20
ASAHI KASEI n Serial Control Interface The AK4120 is controlled via registers. Internal registers can be written using one of two control modes, I2C or 3-wire, that are selected via I2C pin. PDN = “L” initializes the registers to their ...
Page 21
I C-bus Control Mode (I2C= “H”) 2 The AK4120 supports the standard I C-bus interface (max:100kHz). Then AK4120 cannot support fast-mode I 400kHz). (2)-1. WRITE Operations Figure 11 shows the data transfer sequence in I HIGH to LOW ...
Page 22
READ Operations To enable a READ operation in the AK4120, set R/WN bit = “1”. After transmission of data, the master can read the next data address by generating an acknowledge instead of terminating the write cycle after the ...
Page 23
ASAHI KASEI SDA start condition ...
Page 24
System Reset The AK4120 is reset by bringing the power down pin “PDN” =“L”. The digital filters are also reset when this occurs. The AK4120 should be reset once by bringing PDN =“L” upon power-up. After a reset, the ...
Page 25
ASAHI KASEI n Mapping of Program Registers Addr Register Name D7 00H Control 1 PW 01H Control 2 0 02H Control 3 MUTE2R 03H Lch Volume#1 Control 0 04H Rch Volume#1 Control 0 05H Lch Volume#2 Control 0 06H Lch ...
Page 26
ASAHI KASEI ZTM1-0:Duration of zero-crossing timeout when ZELM= “0” ZTM1 Note the output sample rate ZELM: Select Zero Crossing Enable 0: Enable (Default) 1: Disable Addr Register Name 02H Control 3 Default PATH1-0: Path ...
Page 27
ASAHI KASEI Addr Register Name 03H Lch Volume#1 Control 04H Rch Volume#1 Control 05H Lch Volume#2 Control 06H Rch Volume#2 Control Default GAIN6-0: Volume control shown in Table 10 . Volume Range: -83.25dB 12dB(Step 0.75dB) GAIN6-0 00H 01H 02H 9H ...
Page 28
ASAHI KASEI Figure 21 illustrates a typical system connection diagram. An evaluation board is available which demonstrates this application circuit, the optimum layout, power supply arrangement and performance measurement results. Condition: VDD=3.3V, 3-wire serial control mode, Chip Address = “10” ...
Page 29
ASAHI KASEI 24pin VSOP (Unit *7.8 0. 0.22 0.1 Seating Plane 0.10 NOTE: Dimension "*" does not include mold flash. n Package & Lead frame material Package molding compound: Lead frame material: Lead frame surface ...
Page 30
... MS0134-E- AK4120VF AAXXXX Contents of AAXXXX AA: Lot# ...