HFBR-5803A HP [Agilent(Hewlett-Packard)], HFBR-5803A Datasheet
HFBR-5803A
Related parts for HFBR-5803A
HFBR-5803A Summary of contents
Page 1
... Agilent Component Field Sales Offices and Authorized Distributors world wide. 0 °C to +70 °C HFBR-5803/5803T -10 °C TO +85 °C HFBR-5803A/5803AT Features • Full compliance with the optical performance requirements of the FDDI PMD standard • Full compliance with the FDDI LCF-PMD standard • ...
Page 2
... PECL logic signals, ECL referenced (shifted +3 supply, into an analog LED drive current. Receiver Sections The receiver sections of the HFBR-5803 and HFBR-5805 series utilize InGaAs PIN photo- diodes coupled to a custom silicon transimpedance preamplifier IC. These are packaged in the optical sub- assembly portion of the receiver ...
Page 3
... ELECTRICAL SUBASSEMBLY DIFFERENTIAL DATA OUT SINGLE-ENDED SIGNAL QUANTIZER IC DETECT OUT DIFFERENTIAL DATA IN DRIVER IC TOP VIEW Figure 1a. ST Connector Block Diagram. Case Temperature Measurement Point 25.40 (1.000) HFBR-5803 AGILENT DATE CODE (YYWW) SINGAPORE + 0.08 0.75 – 0.05 3.30 ± 0.38 + 0.003 10.35 ) (0.030 (0.130 ± 0.015) – 0.002 (0.407) 2.92 (0 ...
Page 4
... MAX. (1.000) HFBR-5803T DATE CODE (YYWW) SINGAPORE 12.0 MAX. (0.471) 3.2 (0.126) 0.46 Ø (0.018) NOTE 1 20.32 [(8x (2.54/0.100)] 17.4 (0.800) (0.685) 22.86 21.4 (0.900) (0.843) 3.6 (0.142) 1.3 (0.051) NOTE 1: PHOSPHOR BRONZE IS THE BASE MATERIAL FOR THE POSTS & PINS WITH TIN LEAD OVER NICKEL PLATING. DIMENSIONS IN MILLIMETERS (INCHES). ...
Page 5
... The cable parameters used come from the ISO/IEC JTC1/SC 25/ WG3 Generic Cabling for Customer Premises per DIS 11801 document and the EIA/TIA-568-A Commercial Building Telecommunications Cabling Standard per SP-2840. 12 HFBR-5803, 62.5/125 µ HFBR-5803 50/125 µ 0.3 0.5 1 ...
Page 6
... µ µH COIL OR FERRITE INDUCTOR. Figure 7. Recommended Decoupling and Termination Circuits damage which may be induced by electrostatic discharge (ESD). The HFBR-5800 series of transceivers meet MIL-STD-883C Method 3015.4 Class 2 products. Care should be used to avoid shorting the receiver data or signal detect outputs directly to ground without proper current limiting impedance ...
Page 7
Solder and Wash Process Compatibility The transceivers are delivered with protective process plugs inserted into the duplex SC or duplex ST connector receptacle. This process plug protects the optical subassemblies during wave solder and aqueous wash processing and acts as ...
Page 8
NOTE 1: MINIMUM DISTANCE FROM FRONT OF CONNECTOR TO THE PANEL FACE. Figure 8a. Recommended Common Mechanical Layout for SC and Connectored Transceivers. Regulatory Compliance These transceiver products are intended to enable ...
Page 9
... TRANSMITTER OUTPUT OPTICAL C CENTER WAVELENGTH - nm HFBR-5803 FDDI TRANSMITTER TEST RESULTS AND tr/f ARE CORRELATED AND C COMPLY WITH THE ALLOWED SPECTRAL WIDTH AS A FUNCTION OF CENTER WAVELENGTH FOR VARIOUS RISE AND FALL TIMES. Figure 9. Transmitter Output Optical Spectral Width (FWHM) vs. Transmitter Output Optical Center Wavelength and Rise/Fall Times ...
Page 10
... TIME INTERVAL 0.10 0.025 0.0 -0.025 -0.05 5.6 10.0 THE HFBR-5803 OUTPUT OPTICAL PULSE SHAPE SHALL FIT WITHIN THE BOUNDARIES OF THE PULSE ENVELOPE FOR RISE AND FALL TIME MEASUREMENTS. Figure 10. Output Optical Pulse Envelope -10 2 BER 2 -12 1 BER ...
Page 11
SIGNAL _ DETECT (ON) SIGNAL _ DETECT (OFF MAX - MAXIMUM ACQUISITION TIME (SIGNAL MAX IS THE MAXIMUM SIGNAL _ DETECT ASSERTION TIME FOR THE STATION MAX SHALL NOT EXCEED ...
Page 12
... B. Ambient Operating Temperature corresponds to transceiver case temperature of -10 °C mininum to +100 °C maximum with necessary airflow applied. Recommended case temperature measurement point can be found in Figure 2. Transmitter Electrical Characteristics (HFBR-5803/5803T 0°C to +70° (HFBR-5803A/HFBR-5803AT -10°C to +85° Parameter Supply Current Power Dissipation ...
Page 13
... Signal Detect Output Voltage - Low Signal Detect Output Voltage - High Signal Detect Output Rise Time Signal Detect Output Fall Time Transmitter Optical Characteristics (HFBR-5803/5803T 0°C to +70° (HFBR-5803A/HFBR-5803AT -10°C to +85° Parameter Output Optical Power BOL 62.5/125 µ 0.275 Fiber EOL ...
Page 14
... Receiver Optical and Electrical Characteristics (HFBR-5803/5803T 0°C to +70° (HFBR-5803A/HFBR-5803AT -10°C to +85° Parameter Input Optical Power Minimum at Window Edge Input Optical Power Minimum at Eye Center Input Optical Power Maximum Operating Wavelength Duty Cycle Distortion Contributed by the Receiver ...
Page 15
This parameter complies with the FDDI PMD requirements for the trade-offs between center wavelength, spectral width, and rise/ fall times shown in Figure 9. 15. This parameter complies with the optical pulse envelope from the FDDI PMD shown in ...
Page 16
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) ...