AM42-0007_1 MACOM [Tyco Electronics], AM42-0007_1 Datasheet - Page 2

• Manufacturer Part Number: AM42-0007_1
• Description: GaAs MMIC VSAT Power Amplifier 1.4W 14.0 - 14.5GHz
• Manufacturer: MACOM [Tyco Electronics]

2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
GaAs MMIC VSAT Power Amplifier, 2.0 W
14.0 - 14.5 GHz
Absolute Maximum Ratings
Electrical Specifications: T
2. Exceeding any one or combination of these limits may cause
3. M/A-COM does not recommend sustained operation near
4. Case Temperature (T
1. IP
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
permanent damage to this device.
these survivability limits.
Saturated Output Power
Detector Output Voltage
Power Added Efficiency
Output Power at P1dB
Channel Temperature
Storage Temperature
3
Thermal Resistance
is measured with two +24 dBm output tones @ 1 MHz spacing
Power Dissipation
RF Input Power
Output VSWR
Parameter
Input VSWR
Bias Current
Parameter
Linear Gain
Output IP3
V
V
I
DS
DD
GG
1
C
) = +25°C.
Absolute Maximum
-65°C to +150°C
A
-10 Volts
+23 dBm
2100 mA
R
2,3,4
12 Volts
13.2 W
150°C
= +25°C, V
L
= 10 K Ω, P
Test Conditions
25°C Heat Sink
P
P
P
P
P
P
IN
IN
IN
IN
IN
IN
= +14 dBm
= +14 dBm
= +14 dBm
< 0 dBm
< 0 dBm
< 0 dBm
—
OUT
DD
= +31dBm
= +9 V, V
Compliant
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macom.com for additional data sheets and product information.
Typical Bias Configuration
5. Nominal bias is obtained by first connecting –5 volts to pin 4
6. RF ground and thermal interface is the flange (case bottom).
7. No DC bias voltage appears at the RF ports.
8. For optimum IP3 performance, the V
9. Resistor and capacitors surrounding the amplifier are
(V
sequence.
Adequate heat sinking is required.
should be placed within 0.5 inches of pin 6.
suggestions and not included as part of the AM42-0007.
GG
RoHS
GG
), followed by connection +9 volts to pin 6 (V
=- 5.0 V, Z
RF In
3
Units
Ratio
Ratio
°C/W
dBm
dBm
dBm
10 K Ω
mA
dB
1,2,5,9,10
%
V
GND
V
7
DET
AM42-0007
0
= 50Ω, F = 14.0-14.5 GHz
Min.
19
31
—
—
—
—
—
—
—
—
0.01 µF
V
3.3 µF
0.01 µF
GG
4
V
DD
6
DD
Typ.
5,6,7,8,9
bypass capacitors
2.5:1
2.7:1
+3.5
9.5
22
33
32
41
22
18
AM42-0007
RF Out
8
DD
). Note
Max.
2.7:1
25
—
—
—
—
—
—
—
—
V5