K4S510732B-TC1H SAMSUNG [Samsung semiconductor], K4S510732B-TC1H Datasheet
![no-image](/images/no-image-200.jpg)
K4S510732B-TC1H
Related parts for K4S510732B-TC1H
K4S510732B-TC1H Summary of contents
Page 1
... K4S510732B Stacked 512Mbit SDRAM * Samsung Electronics reserves the right to change products or specification without 16M x 8bit x 4 Banks Synchronous DRAM LVTTL Revision 0.0 Feb. 2001 Preliminary CMOS SDRAM Rev. 0.0 Feb.2001 ...
Page 2
... K4S510732B Revision 0.0 (Feb., 2001) Preliminary CMOS SDRAM Rev. 0.0 Feb.2001 ...
Page 3
... Staktek’ s stacking technology is Samsung’ s stacking technology of choice. CMOS SDRAM GENERAL DESCRIPTION The K4S510732B is 536,870,912 bits synchronous high data rate Dynamic RAM organized 16,777,216 words by 8 bits, fabri- cated with SAMSUNG's high performance CMOS technology. Syn- chronous design allows precise cycle control with the use of system clock I/O transactions are possible on every clock cycle ...
Page 4
... K4S510732B PIN CONFIGURATION (Top view) PIN FUNCTION DESCRIPTION Pin Name CLK System clock CS0~1 Chip select CKE0~1 Clock enable Address Bank select address 0 1 RAS Row address strobe CAS Column address strobe WE Write enable DQM Data input/output mask ...
Page 5
... K4S510732B ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Voltage on V supply relative to Vss DD Storage temperature Power dissipation Short circuit current Note : Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. ...
Page 6
... CC3 Operating current I CC4 (Burst mode) Refresh current I CC5 Self refresh current I CC6 Notes : 1. Measured with outputs open. 2. Refresh period is 64ms. 3. K4S510732B-TC** 4. K4S510732B-TL** 5. Unless otherwise noticed, input swing level is CMOS Test Condition Burst length = (min ...
Page 7
... K4S510732B AC OPERATING TEST CONDITIONS Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition 3.3V 1200 Output 50pF 870 (Fig output load circuit OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) ...
Page 8
... K4S510732B AC CHARACTERISTICS (AC operating conditions unless otherwise noted) Parameter CAS latency=3 CLK cycle time CAS latency=2 CAS latency=3 CLK to valid output delay CAS latency=2 CAS latency=3 Output data hold time CAS latency=2 CLK high pulse width CLK low pulse width Input setup time ...
Page 9
... K4S510732B IBIS SPECIFICATION I Characteristics (Pull-up) OH 100MHz/ 100MHz/ Voltage 133MHz 133MHz Min Max (V) I (mA) I (mA) 3.45 -2.4 3.3 -27.3 3.0 0.0 -74.1 2.6 -21.1 -129.2 2.4 -34.1 -153.3 2.0 -58.7 -197.0 1.8 -67.3 -226.2 1.65 -73.0 -248.0 1.5 -77.9 -269.7 1.4 -80.8 -284.3 1.0 -88.6 -344.5 0.0 -93.0 -502.4 I Characteristics (Pull-down) OL 100MHz/ 100MHz/ Voltage 133MHz 133MHz Min Max (V) I (mA) I (mA) 0 0.0 0.0 0.4 27.5 70.2 0.65 41.8 107.5 0.85 51.6 133.8 1 58.0 151.2 1.4 70.7 187.7 1.5 72.9 194.4 1.65 75.4 202.5 1 ...
Page 10
... K4S510732B V Clamp @ CLK, CKE, CS, DQM & (V) I (mA) DD 0.0 0.0 0.2 0.0 0.4 0.0 0.6 0.0 0.7 0.0 0.8 0.0 0.9 0.0 1.0 0.23 1.2 1.34 1.4 3.02 1.6 5.06 1.8 7.35 2.0 9.83 2.2 12.48 2.4 15.30 2.6 18.31 V Clamp @ CLK, CKE, CS, DQM & (V) I (mA) SS -2.6 -57.23 -2.4 -45.77 -2.2 -38.26 -2.0 -31.22 -1.8 -24.58 -1.6 -18.37 -1.4 -12.56 -1.2 -7.57 -1.0 -3.37 -0.9 -1.75 -0.8 -0.58 -0.7 -0.05 -0.6 0.0 -0.4 0.0 -0.2 0.0 0.0 0.0 CMOS SDRAM Minimum V clamp current DD (Referenced Voltage I (mA) Minimum V clamp current -10 -20 -30 -40 -50 -60 Voltage I (mA) Rev ...
Page 11
... K4S510732B SIMPLIFIED TRUTH TABLE Command Register Mode register set Auto refresh Entry Refresh Self refresh Exit Bank active & row addr. Read & Auto precharge disable column address Auto precharge enable Write & Auto precharge disable column address Auto precharge enable ...