M464S0824DT1-C1H SAMSUNG [Samsung semiconductor], M464S0824DT1-C1H Datasheet
M464S0824DT1-C1H
Related parts for M464S0824DT1-C1H
M464S0824DT1-C1H Summary of contents
Page 1
... M464S0824DT1 SDRAM SODIMM 8Mx64 SDRAM SODIMM based on 4Mx16, 4Banks, 4K Refresh, 3.3V Synchronous DRAMs with SPD GENERAL DESCRIPTION The Samsung M464S0824DT1 bit x 64 Synchronous Dynamic RAM high density memory module. The Samsung M464S0824DT1 consists of eight CMOS bit with 4banks Synchronous DRAMs in TSOP-II 400mil package and a 2K EEPROM in 8-pin TSSOP package on a 144-pin glass-epoxy substrate ...
Page 2
... M464S0824DT1 PIN CONFIGURATION DESCRIPTION Pin Name CLK System clock CS Chip select CKE Clock enable A0 ~ A11 Address BA0 ~ BA1 Bank select address RAS Row address strobe CAS Column address strobe WE Write enable DQM0 ~ 7 Data input/output mask DQ ~ Data input/output Power supply/ground ...
Page 3
... M464S0824DT1 FUNCTIONAL BLOCK DIAGRAM CS1 CS0 DQM0 LDQM CS DQ0 DQ0 DQ1 DQ1 DQ2 DQ2 U0 DQ3 DQ3 DQ4 DQ4 DQ5 DQ5 DQ6 DQ6 DQ7 DQ7 UDQM DQM1 DQ8 DQ8 DQ9 DQ9 DQ10 DQ10 DQ11 DQ11 DQ12 DQ12 DQ13 DQ13 DQ14 DQ14 DQ15 ...
Page 4
... M464S0824DT1 ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Voltage on V supply relative to Vss DD Storage temperature Power dissipation Short circuit current Note : Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. ...
Page 5
... M464S0824DT1 DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, T Parameter Symbol Operating current (One bank active) I Precharge standby current in power-down mode I CC2 I Precharge standby current in non power-down mode I CC2 I Active standby current in power-down mode I CC3 I Active standby current in non power-down mode (One bank active) ...
Page 6
... M464S0824DT1 AC OPERATING TEST CONDITIONS Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition 3.3V Output 870 (Fig output load circuit OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) Parameter ...
Page 7
... M464S0824DT1 AC CHARACTERISTICS (AC operating conditions unless otherwise noted) REFER TO THE INDIVIDUAL COMPONENT, NOT THE WHOLE MODULE. Parameter CAS latency=3 CLK cycle time CAS latency=2 CAS latency=3 CLK to valid output delay CAS latency=2 CAS latency=3 Output data hold time CAS latency=2 CLK high pulse width ...
Page 8
... M464S0824DT1 SIMPLIFIED TRUTH TABLE Command Register Mode register set Auto refresh Entry Refresh Self refresh Exit Bank active & row addr. Read & Auto precharge disable column address Auto precharge enable Write & Auto precharge disable column address Auto precharge enable ...
Page 9
... M464S0824DT1 PACKAGE DIMENSIONS 0.16 0.039 (4.00 0.10) 1 0.13 (3.30) 0.15 (3.70) 2 0.150 Max (3.80 Max) 0.04 0.0039 (1.00 0.10) Tolerances : .006(.15) unless otherwise specified The used device is 4Mx16 SDRAM, TSOP SDRAM Part No. : K4S641632D 2.66 (67.56) 2.50 (63.60 0.91 1.29 (23.20) (32.80) 0.18 (4.60) 0.083 (2.10) 0.10 (2.50 0.16 0.0039 (4.00 0.10) 0.06 0.0039 (1.50 0.1) Detail Z PC100 SODIMM Units : Inches (Millimeters) 2-R 0.078 Min (2.00 Min) 143 2- 0.07 (1.80) Y 144 0.024 ...