HFDOM40KB016 HANBIT [Hanbit Electronics Co.,Ltd], HFDOM40KB016 Datasheet

Page 1

HANBit 40Pin Flash Disk Module Min.8MB ~ Max.1GB, True IDE Interface Mode, 3.3V / 5.0V Operating 1. PRODUCT OVERVIEW GENERAL DESCRIPTION The HFDOM40KVxxx series 40Pin Flash Disk Module is a flash technology based with True IDE interface flash memory card. ...

Page 2

HANBit Operating Voltage : 3.3V / 5.0V Power consumption : 3.3V ± 5% Read mode <30 mA Write mode <56 mA Stop mode <2 mA Environment conditions : Operating temperature Storage temperature Relative humidity ELECTRICAL SPECIFICATIONS Table 1.1 Absolute Maximum ...

Page 3

... HANBit CAPACITY SPECIFICATIONS Table 1.4 Capacity Specifications Part Number Capacity (formatted) HFDOM40KB016 HFDOM40KB032 30,65 Mbytes HFDOM40KB064 61,32 Mbytes HFDOM40KB096 91,98 Mbytes 122,64 Mbytes HFDOM40KB128 119,65 Mbytes HFDOM40KB192 183,96 Mbytes 245,28 Mbytes HFDOM40KB256 239,29 Mbytes 369,91 Mbytes HFDOM40KB384 357,86 Mbytes URL:www.hbe.co.kr Rev. 1.1 (December, 2003) Cylinders Heads ...

Page 4

HANBit PHYSYCAL SPECIFICATION 22.10±0.1mm 29.0±0.2mm 7.0±0.1mm 2.54±0.05mm Figure 1.1 40 pin Type Flash Disk Module Dimensions URL:www.hbe.co.kr Rev. 1.1 (December, 2003) 51.85±0.1mm Jumper Master Slave 1,2 2,3 Close Close 1 55.37±0.1mm < View from front side > 3.8±0.1mm 2.54±0.05mm 48.20±0.1mm ...

Page 5

HANBit INSTALLTION GUIDE 1) Setting Method ① Make sure your computer is turned off before you open the case. ② Plug the carefully into the 40pin IDE slot on your computer. Caution: Make sure to align pin1 on host adapter ...

Page 6

HANBit 2. PIN INFORMATION PIN ASSIGNMENTS AND PIN TYPE Table 2.1 Pin Assignment and Pin type Pin Signal 1 /RESET 3 D07 5 D06 7 D05 9 D04 11 D03 13 D02 15 D01 17 D00 19 GND 21 INPACK ...

Page 7

HANBit Signal Descriptions Table 2.2 Signal Descriptions Signal Name Dir. Pin A[2:0] I 33,35,36 -PDIAG I/O 34 -DASP I/O 39 -CS0, -CS1 I 37,38 3,4,5,6, 7,8,9,10, D[15:00] I/O 11,12,13, 14,15,16, 17,18 2,19,22, GND -- 24,26, 30,40, -IOR I 25 -IOW ...

Page 8

HANBit BLOCK DIAGRAM PCMCIA ATA Interface HOST ATA Interface Interface RAM 3. INTERFACE BUS TIMING ACCESS SPCIFICATIONS 1 System clock timing Sym. Description Tc Clock cycle time Tlpd Clock low pulse duration Thpd Clock high pulse duration URL:www.hbe.co.kr Rev. 1.1 ...

Page 9

HANBit 2 Host Read/Write timing Sym bus asserted from HIOR# / HOE hold time after HIOR# / HOE# ( set up time of HIOW# / HWE# ( hold time of HIOW# / ...

Page 10

HANBit REGISTERS 1) Data Register (Address – 1F0h[170h];Offset 0,8,9) The Data Register is a 16-bit register, and it is used to transfer data blocks between the CompactFlash Storage Card data buffer and the Host. This register overlaps the Error Register.The ...

Page 11

HANBit This register contains the numbers of sectors of data requested to be transferred on a read or write operation between the host and the CompactFlash Storage Card. If the value in this register is zero, a count of 256 ...

Page 12

HANBit D7 D6 BUSY RDY Bit 7 (BUSY): the busy bit is set when the CompactFlash Storage Card has access to the command buffer and registers and the host is locked out from accessing the command register and buffer. No ...

Page 13

HANBit Implementation Note: Conflicts may occur on the host data bus when this bit is provided by a Floppy Disk Controller operating at the same addresses as the CompactFlash Storage Card. Following are some possible solutions to this problem for ...

Page 14

HANBit 1 Set Sleep Mode 1 Stand By 1 Stand By Immediate 1 Translate Sector 1 Wear Level 2 Write Buffer 2 Write Long Sector 3 Write Multiple 3 WriteMultiple w/o Erase 2 Write Sector(s) 2 Write Sector(s) w/o Erase ...

Page 15

HANBit Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command performs the internal diagnostic tests implemented by the CompactFlash Storage Card PCMCIA configuration this command runs only on the CompactFlash Storage Card which is addressed by ...

Page 16

HANBit C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command writes the desired head and cylinder of the selected drive with a vendor unique data pattern (typically FFh or 00h). To remain host backward compatible, the ...

Page 17

HANBit 10-19 aaaa 20 20 xxxxh 2 21 xxxxh 2 22 0004h 2 23-26 aaaa 8 27-46 aaaa 40 47 xxxxh 2 48 0000h 2 49 xx00h 2 50 0000h 2 51 0x00h 2 52 0000h 2 53 0001h 2 ...

Page 18

HANBit Idle Immediate – 95h or E1h Bit-> 7 Command(7) C/D/H(6) X Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an ...

Page 19

HANBit Read Multiple – C4h Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) The Read Multiple command performs similarly to the Read Sectors command. Interrupts are not generated on every sector, but on the ...

Page 20

HANBit The Read Long command performs similarly to the Read Sector(s) command except that it returns 516 bytes of data instead of 512 bytes. During a Read Long command, the CompactFlash Storage Card does not check the ECC bytes to ...

Page 21

HANBit Recablibrate – 1Xh Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command is effectively a NOP command to the CompactFlash Storage Card and is provided for compatibility purposes. Request Sense – 03h ...

Page 22

HANBit 18h 05h , 30-34h , 37h ,3Eh 10h , 14h 3Ah 1Fh 0Ch , 38h , 3Bh , 3Ch , 3Fh 03h 22h Seek –7X h Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) ...

Page 23

HANBit 55h Disable Read Look Ahead 66h Disable Power on Reset(POR) establishment of defaults at Soft Reset 69h NOP – Accepted for backward compatibility 81h Disable 8 – bit data transfer 8Ah Disable Power Level 1 commands 96h NOP – ...

Page 24

HANBit commands are disabled. At power on, or after a hardware or (unless disabled by a Set Feature command) software reset, the default mode is Read and Write Multiple disabled. Set Sleep Mode – 99h or E6h Bit-> 7 Command(7) ...

Page 25

HANBit Sec Cnt(2) Feature(1) This command causes the CompactFlash Storage Card to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately. Recovery from sleep mode is accomplished by simply ...

Page 26

HANBit Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) For the CompactFlash Storage Cards that do not support security mode feature set, this command is effectively a NOP command and only implemented for backward compatibility. The Sector Count Register ...

Page 27

HANBit recommended. Write Multiple Command – C5h Bit-> 7 Command(7) C/D/H(6) X Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) Note: The current revision of the CompactFlash Storage Card only supports a block count indicated in ...

Page 28

HANBit operation is not performed. The sectors should be pre-erased with the Erase Sector(s) command before this command is issued. Write Sector(s) – 30h or 31h Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) ...

Page 29

HANBit Bit-> 7 Command(7) C/D/H(6) 1 Cyl High(5) Cyl Low(4) Sec Num(3) Sec Cnt(2) Feature(1) This command is similar to the Write Sector(s) command, except each sector is verified immediately after being written. This command has the same protocol as ...

Page 30

HANBit Write Buffer Write Long Sector Write Multiple Write Multiple w/o Erase Write Sector(s) Write Sector(s) w/o Erase Write Verify Sector(s) Invalid Command Code V = Valid on this command Ordering Infomation NO Parts Capacity 1 16Mbyte DOM40KV016 2 32Mbyte ...