MPM-15 MPD [MicroPower Direct, LLC], MPM-15 Datasheet - Page 2

• Manufacturer Part Number: MPM-15
• Description: Compact, 15W PC Mount Single, Dual & Triple Out AC/DC Power Supplies
• Manufacturer: MPD [MicroPower Direct, LLC]

Model Selection Guide
Notes:
1.
2. The MPM-15 series is specifi ed for operation over the wide operating temperature
3. It is recommended that a fuse be used on the input of a power supply for protection.
Mechanical Dimensions
Notes:
•
•
MPM-15S-03
MPM-15S-05
MPM-15S-12
MPM-15S-15
MPM-15S-24
MPM-15S-48
MPM-15D-05
MPM-15D-12
MPM-15D-15
MPM-15T-0505
MPM-15T-0512
MPM-15T-0515
MPM-15T-0524
All dimensions are typical in inches (mm)
Tolerance x.xx =
Load regulation is measured for an output change of 10% to 90% at nominal input
line. For multiple output models, the loads are balanced.
range of -20°C to +55°C without derating. For operation over +55°C, derate the
power linearly by 3.75%/°C from +55°C to +70°C.
For the MPM-15 series, a 2A/250 VAC slow blow should be used.
Number
Model
±
115
0.01 (
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
292 Page Street Ste D Stoughton, MA 02072
Current
MicroPower Direct
VAC
Pin Connections
±
Pin
Input
0.25)
1
2
3
4
5
6
7
8
230
AC-Neutral AC-Neutral AC-Neutral
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
0.14
(A)
AC-Line
No Pin
No Pin
No Pin
No Pin
Single
VAC
+Vo 1
-Vo 1
Voltage
(VDC)
+12.0
+15.0
+5.0
12.0
15.0
24.0
48.0
www.micropowerdirect.com
3.3
5.0
5.0
5.0
5.0
5.0
AC-Ground AC-Ground
Common
AC-Line
No Pin
No Pin
+Vo 1
-Vo 2
Dual
Output 1
3.000
2.800
1.250
1.000
0.625
0.320
+1.50
+0.65
+0.50
Typ.
2.60
2.00
1.80
2.00
Current
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±1.0%
±2.0%
±2.0%
±2.0%
±3.0%
±3.0%
±3.0%
±3.0%
Load
Reg.
Common
(Vout 1)
(A)
AC-Line
Triple
+Vo 1
+Vo 2
-Vo 1
-Vo 2
Protection
Over Volt.
(VDC)
•
20.0
20.0
30.0
30.0
20.0
20.0
6.5
6.5
6.5
6.5
6.5
6.5
6.5
TEL: [phone]
Voltage
(VDC)
+12.0 +0.20 ±5.0%
+15.0 +0.20 ±5.0%
+24.0 +0.10 ±5.0%
-12.0
-15.0
+5.0 +0.20 ±5.0%
-5.0
Typical Connection
Typical Component Values
Notes:
1. C1, C3 and C5 are high frequency, low resistance electrolytic capacitors.
Vout
12.0
15.0
24.0
48.0
Refer to the suppliers specifi cations for capacitance/current ratings.
Output 2
3.3
5.0
-1.50 ±2.0%
-0.65 ±2.0%
-0.50 ±2.0%
Typ.
Current
•
330 ~ 1,000 µF/16V
330 ~ 1,000 µF/16V
FAX: [phone]
Load
Reg.
(Vout 2)
(A)
220 µF/25V
220 µF/25V
120 µF/35V
C1, C3, C5
68 µF/63V
Protection
Over Volt.
(VDC)
20.0
20.0
6.5
2. Voltage derating on all capacitors should be
3. C2, C4 and C6 eliminate high frequency noise.
4. The TVS is recommended to protect load
80% or higher.
circuitry in the event of a module failure.
Voltage
•
(VDC)
0.1 µF/50V
C2, C4, C6
-12.0
-15.0
-24.0
Ceramic
Output 3
E-Mail: [e-mail]
-5.0
-0.20 ±5.0%
-0.20 ±5.0%
-0.20 ±5.0%
-0.10 ±5.0%
Typ.
Current
(Vout 3)
Slow Blow
250 VAC
Fuse
2A/
Load
Reg.
(A)
Effi ciency
P6KE6.8A
P6KE6.8A
P6KE16A
P6KE20A
P6KE33A
P6KE62A
(%, Typ)
TVS
80
80
80
80
80
80
80
80
80
80
80
80
80