CXOMHG STATEK [STATEK CORPORATION], CXOMHG Datasheet - Page 2

no-image

CXOMHG

Manufacturer Part Number
CXOMHG
Description
High Shock, Low Profile, Miniature Surface Mount Crystal Oscillator
Manufacturer
STATEK [STATEK CORPORATION]
Datasheet
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
CXOMHG
HOW TO ORDER CXOMHG SURFACE MOUNT CRYSTAL OSCILLATORS
SPECIFICATIONS
Specifications are typical at 25
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage
Calibration Tolerance
Frequency Stability
Over Temperature
Supply Current (Typical)
Output Load (CMOS)
Start-up Time
Rise/Fall Time
Duty Cycle
Aging, first year
Shock, survival
Vibration, survival
Operating Temp Ranges -10
1. Other voltages available. For 3.3 V, see CXO3MHG data sheet. For others,
2. Other tolerances available.
3. Does not include calibration tolerance. Other tolerances available.
4. Higher CMOS loads and TTL loads available. Contact factory.
5. Higher shock version available. Contact factory for requirements above 10,000 g.
6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
Note: All parameters are measured at ambient temperature with a 10 M , 15 pF load.
PACKAGING OPTIONS
CXOMHG - Tray Pack
available.
contact factory.
“S” if special or
custom design.
Blank if Std.
- 16 mm tape, 7˝or 13˝ reels
5
Per EIA 418
1
S
6
3
4
2
Enable/Disable
10 MHz
24 MHz
30 MHz
40 MHz
50 MHz
15 pF
5.0 V
5 ms MAX
6 ns MAX
40% MIN, 60% MAX
10 ppm MAX
10,000 g, 0.3 ms,
20 g, 10-2,000 Hz swept sine
-40
-55
+ _
+ _
+ _
+ _
E, T, or N
100 ppm
100 ppm for Industrial
100 ppm for Military
Option
(see Tape and Reel data sheet 10109)
50 ppm for Commercial
O
O
O
T
C to +70
C to +85
C to +125
O
C unless otherwise noted.
10 mA
12 mA
14 mA
4 mA
8 mA
Terminations
Blank = SM1
SM3 = Solder Dipped
SM5 = Solder Dipped
O
O
C
C
O
C (Military)
= Gold Plated
1
(Commercial)
(Industrial)
SM3
/
(Lead Free)
2
sine
Frequency
K = kHz
M = MHz
32.0M
,
When enabled (PIN 1 is high*)
When disabled (PIN 1 is low)
When re-enabled (PIN 1 changes from low to high)
*
ENABLE/DISABLE OPTIONS (E/T/N)
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs
and differ in whether the oscillator continues to run
internally when the output is put into the high Z state: it
stops in the E-version and continues to run in the
T-version. So, the E-version offers very low current
consumption when the oscillator is disabled and the
T-version offers very fast output recovery when the
oscillator is re-enabled. The N-version does not have
PIN 1 connected internally and so has no enable/disable
capability. The following table compares the E and T
versions.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage V
Storage Temperature
Maximum Process Temperature 260
When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
ENABLE/DISABLE OPTIONS E AND T
Calibration
Tolerance
Output
Oscillator
Current consumption
Output
Oscillator
Current consumption
Output recovery
@ 25
(in ppm)
100
0
C
/
OR
/
Stability over
Temp.Range
Frequency
(in ppm)
100
COMPARISON OF
DD
/
/
Frequency
Tolerance
(in ppm)
200
Total
Freq. output
Oscillates
Normal
High Z state
Stops
Very low
Delayed
E
/
Temp. Range:
C = -10
I
M = -55
S = Customer Specified
Temp. Range:
C = -10
I
M = -55
S = Customer Specified
-0.5V to 7.0V
-55
= -40
= -40
I
I
O
O
C to +125
C fo 20 seconds
O
O
O
O
O
O
C to +70
C to +85
C to +125
C to +70
C to +85
C to +125
Freq. output
Oscillates
Normal
High Z state
Oscillates
Lower than normal
Immediate
O
O
O
O
C
C
C
C
O
O
O
C
C
C
T
10160 Rev A
Pb

Related parts for CXOMHG