FX828D2 CMLMICRO [CML Microcircuits], FX828D2 Datasheet - Page 17

• Manufacturer Part Number: FX828D2
• Description: CTCSS/DCS/SELCALL Processor
• Manufacturer: CMLMICRO [CML Microcircuits]

CTCSS/DCS/SELCALL Processor
RX TONE
(Bits 3, 2, 1 and 0)
IRQ FLAG Register (Hex address $8F)
This register is used to indicate when the device requires attention as below:
(Bits 7 and 1)
GPT IRQ FLAG
(Bit 6)
COMP 0 to 1
IRQ FLAG
(Bit 5)
COMP 1 to 0
IRQ FLAG
(Bit 4)
TONE IRQ FLAG
(Bit 3)
CTCSS FAST IRQ
FLAG
(Bit 2)
DCS IRQ FLAG
(Bit 0)
© 2009 CML Microsystems Plc
TONE DECODE means that a tone has been decoded and its characteristics
are defined by the bandwidth (See SIGNALLING SET-UP Register bits 7, 6, 5
and 4) and the RX TONE number (See SELCALL and SUB-AUDIO STATUS
Register bits 3, 2, 1 and 0).
When Bit 6 in the SIGNALLING CONTROL Register is set to "0" the TONE
DECODE bit 4 will be set to "0".
Identification of a valid tone which is not in the pre-programmed list of up to 15
tones will cause the decoder to move to the TONE DECODE state with the RX
TONE address of "1111" in bits 3, 2, 1 and 0; indicating a valid, but
unrecognised, tone. Loss of tone, will cause the NOTONE timer to be started.
If loss of tone continues for the duration of the timeout period, then the decoder
will move to NOTONE state and the identification of pre-programmed tones will
start again. The time-out period is not user-adjustable.
These four bits hold a Hex number from $0 to $F. Numbers $0 to $E represent
the address of the tone decoded according to the tones programmed in the RX
TONE PROGRAM Register, $84. The Hex number $F indicates the presence
of any tone that is not described by DECODER BANDWIDTH (Bits 7, 6, 5 and 4,
SIGNALLING SET-UP Register, $82) and FREQUENCY (Bits 11 - 0, RX TONE
PROGRAM Register, $84).
Reserved for future use. These will be set to "0" but should be ignored by user's
software.
When the general purpose timer has reached zero in its internal register, this bit
will be set to "1" to indicate the timeout has expired. This bit is cleared to "0" by
a read of the IRQ FLAG Register (Hex address $8F).
When the comparator output goes from "0" to "1" (i.e. when the input voltage is
above the DAC output voltage) this bit will be set to "1" and an interrupt
generated (if bit 5 of the IRQ MASK Register $8E is set to "1"). This bit is set to
"0" when the IRQ FLAG Register $8F is read.
When the comparator output goes from "1" to "0" this bit will be set to "1" and an
interrupt generated (if bit 4 of the IRQ MASK Register $8E is set to "1"). This bit
is set to "0" when the IRQ FLAG Register $8F is read.
When RX TONE DECODE (Bit 4, SELCALL and SUB-AUDIO STATUS
Register, $81) or Rx TONE (the decoded 4 bit tone address in Register $81)
changes state this bit will be set to "1". This bit is cleared to "0" by a read of the
IRQ FLAG Register (Hex address $8F).
When CTCSS FAST TONE (Bit 6, SELCALL and SUB-AUDIO STATUS
Register, $81) changes state this bit will be set to "1". This bit is cleared to "0"
by a read of the IRQ FLAG Register (Hex address $8F).
When DCS DECODE/NO DECODE (Bit 7 SELCALL and SUB-AUDIO STATUS
Register, $81) changes state this bit will be set to "1". This bit is cleared to "0"
by a read of the IRQ FLAG Register (Hex address $8F).
17
D/828/4
FX828