ICX209 SONY [Sony Corporation], ICX209 Datasheet
ICX209
Related parts for ICX209
ICX209 Summary of contents
Page 1
... Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras Description The ICX209AK is an interline CCD solid-state image sensor suitable for PAL color video cameras. Compared with the current product ICX069AK, sensitivity and saturation signal are improved drastically through the adoption of Super HAD CCD technology. ...
Page 2
... Horizontal register transfer clock 1 H Horizontal register transfer clock 2 Ratings Unit – –50 to +15 V –50 to +0.3 V –40 to +0.3 V –0.3 to +18 V –10 to +18 V – –0.3 to +28 V –0 +15 V – –13 to +13 V –30 to +80 °C –10 to +60 °C ICX209AK Remarks 1 ...
Page 3
... V VL VL3 – High-level coupling V 2 High-level coupling V 2 Low-level coupling V 2 Low-level coupling Input through 0.1µ capacitance V 4 Low-level coupling V 4 Low-level coupling V 5 ICX209AK L )/2 VH2 )/2 VL4 ...
Page 4
... V23 C V13 Horizontal transfer clock equivalent circuit C RG – 4 – Typ. Max. Unit 680 pF 470 pF 330 pF 270 180 pF Ω 82 Ω 15 Ω 12 Ω ICX209AK Remarks H 2 ...
Page 5
... twh VHH V VHL V VHL V VL3 VHL V VLH V VLL V VL4 – 5 – VHH VHH V VHL V VH3 V VLL VHH VHH VHL VHL V VH4 V VLH V VL ICX209AK V VLH ...
Page 6
... CCD) tr twh twl Point A is the minimum value of the coupling waveform during the period from RGLL . RGLm 100% 90% V SUB 10 twh – 6 – twl tr twh tf V RGH RGL is the average value of V RGL ICX209AK and RGLH ...
Page 7
... H two Min. Typ – 7 – Unit Remarks 0.5 0.5 µs 15 250 ns 6.5 9.5 6.5 9.5 ns 6.5 9.5 6.5 9.5 0.01 0.01 µs 0.01 0. 0.5 0.5 µs ) for the H rising side of the Unit Remarks Max and H is two ICX209AK During readout 1 2 During drain charge and ...
Page 8
... S H LPF2 S H (3dB down 1MHz) – 8 – Unit Measurement method Chroma signal output ICX209AK (Ta = 25°C) Remarks Ta = 60°C Zone 0 and I Zone 60° 60°C ...
Page 9
... Ye A1 mixed by pairs such as A1 and A2 in the A field. (pairs such the B field result, the sequence of charges output as signals from Ye A2 the horizontal shift register (Hreg) is, for line A1 Cy), G ( Cy), and (Mg + Ye). Hreg 1/2 1/2 – 9 – ICX209AK ...
Page 10
... Crmin)/200 | ∆ (Cbmax – Cbmin)/200 | 2 , color temperature of 3200K halogen source subject. (Pattern Mg [mV]) at the center of the screen with frame readout Cy 100 [%] (1/10V method conversion value) 100 [%] 100 [%] 100 [%] – 10 – [mV]) and G signal output (S [mV]), and Ye G ICX209AK ...
Page 11
... Adjust the Y signal output value generated by strobe light to 200mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Ylag). Substitute the value into the following formula. Lag = (Ylag/200) 100 [%] FLD V1 Strobe light timing Output Light Y signal output 200mV Ylag (lag) – 11 – ICX209AK ...
Page 12
... ICX209AK ...
Page 13
... Spectral Sensitivity Characteristics (excludes both lens characteristics and light source characteristics) 1.0 0.8 0.6 0.4 0.2 0.0 400 Sensor Readout Clock Timing Chart V1 V2 Odd Field Even Field 450 500 550 Wave Length [nm] 1.5 33.6 0.2 – 13 – 600 650 700 2.6 2.6 2.6 2.6 Unit: µs ICX209AK ...
Page 14
... ICX209AK ...
Page 15
... ICX209AK ...
Page 16
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N 50N Compressive strength – 16 – ICX209AK 1.2Nm Torsional strength ...
Page 17
... This package has 2 kinds of internal structure. However, their package outline, optical size, and strength are the same. Cross section of lead frame The cross section of lead frame can be seen on the side of the package for structure A. Structure A Package Chip Metal plate (lead frame) – 17 – ICX209AK Structure B ...
Page 18
... ICX209AK ...