PIC-P18B ETC2 [List of Unclassifed Manufacturers], PIC-P18B Datasheet

PIC-P18B

Manufacturer Part Number

PIC-P18B

Description

PROTOTYPE BOARD FOR 18 PIN PIC MICROCONTROLLERS

Manufacturer

ETC2 [List of Unclassifed Manufacturers]

Datasheet

1.PIC-P18B.pdf (2 pages)

Current page: 1 of 2
Download datasheet (76Kb)

Features:

PIC-P18B is prototype board for 18 pin PIC

microcontrollers with following features:

Programming:

To program PIC-P18B you need serial port or

parallel port PIC programmers with ICSP

connector (PIC-PG1, PIC-PG3B) or PIC-ICD1-

The serial port ICSP programmer (PIC-PG1)

works with IC PROG ICPROG software,

by Bonny Gijzen. T

may

http://www.icprog.com

The parallel port ICSP programmer (PIC-PG3B)

works with Bojan Dobaj’s shareware software

- RS232 Tx, Rx interface with MAX232 IC

- ICD/ICSP 6 pin connector

- Status

- 4MHz, or 20MHz quartz oscillator

- extension slot on each microcontroller pin

- DIL18 microcontroller socket

- power supply plug in connector

- +5V power supply voltage regulator

- 0.1” (2.54 mm) grid

- dimensions: 100x80 mm

- four mounting holes

removable jumper

Development boards for PIC, AVR and MSP430 microcontrollers

LED

download

he latest release of ICPROG

connected

FOR 18 PIN PIC MICROCONTROLLERS

for

PIC-P18B PROTOTYPE BOARD

free

RB3

written

from

via

from

Goodwin’s

www.lpilsley.uklinux.net

ICD/ICSP connector layout:

The ICD/ICSP connector is 6 pin with 0,1" step.

The PIN.1 is marked with square pad on bottom

and arrow on top. ICSP signals are: 1- MCLR, 2-

VDD, 3- VSS/GND, 4- PGD/RB7, 5- PGC/RB6,

6- PGM/RB3.

RS232 interface:

J2 removable jumper selects where RTS/DTR

line to be connected. In position 12 the line is

connected to RTS, in position 23 is connected to

DTR.

Status LED:

Connected to RB3 via removable jumper J2. The

jumper should be left open while programming.

Oscillator circuit:

Crystal resonator connected to OSC1 and OSC2.

Supported devices:

All 18 pin PIC microcontrollers.

Power supply:

The power supply should be in range +7.5

+18VDC.

Ordering codes:

PIC-P18B-4MHz

PIC-P18B-20MHz

PIC-P18B/PCB

http://www.picallw.com

http://www.olimex.com/dev

free

- assembled and tested

- only PCB

software

Nigel

from

Related parts for PIC-P18B

PIC-P18B Summary of contents

Page 1

... Programming: To program PIC-P18B you need serial port or parallel port PIC programmers with ICSP connector (PIC-PG1, PIC-PG3B) or PIC-ICD1- B. The serial port ICSP programmer (PIC-PG1) works with IC PROG ICPROG software, he latest release of ICPROG by Bonny Gijzen ...

Page 2

...

Related keywords

PIC-P18B datasheet
PIC-P18B data sheet
PIC-P18B pdf datasheet
PIC-P18B component
PIC-P18B part
PIC-P18B distributor
PIC-P18B RoHS
PIC-P18B datasheet download