HCMS-39X2 HP [Agilent(Hewlett-Packard)], HCMS-39X2 Datasheet
HCMS-39X2
Related parts for HCMS-39X2
HCMS-39X2 Summary of contents
Page 1
... CMOS ESD WARNING: STANDARD CMOS HANDLING PRECAUTIONS SHOULD BE OBSERVED TO AVOID STATIC DISCHARGE Agilent HCMS-39x2 and HCMS-39x4 3.3 V High Performance CMOS 5x7 AlphaNumeric Displays Data Sheet IC. Each display can be directly ...
Page 2
... PIN # 1 0.51 ± 0.13 TYP. (0.020 ± 0.005) NOTES: 1. DIMENSIONS ARE IN mm (INCHES). 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH). 3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY. Figure 1. HCMS-390X package dimensions. 2 4.45 (0.175) TYP. 2.22 (0.087) SYM 10.16 (0.400) MAX. 2.11 (0.083) TYP. DATE CODE ...
Page 3
... PART NUMBER HCMS-391x YYWW 0.51 (0.020) 0.51 ± 0.13 TYP. (0.020 ± 0.005) NOTES: 1. DIMENSIONS ARE IN mm (INCHES). 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH). 3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY. Figure 2. HCMS-391X Package dimensions. 3 4.45 TYP. (0.175) 10.16 (0.400) MAX 2.11 (0.083) TYP. ...
Page 4
... TYP. (0.020 ± 0.005) NOTES: 1. DIMENSIONS ARE IN mm (INCHES). 2. UNLESS OTHERWISE SPECIFIED, THE TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH). 3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY. Figure 3. HCMS-396X Package dimensions. 4 2.54 (0.100) TYP. 3 11.43 (0.450) MAX. DATE CODE (YEAR, WEEK) INTENSITY CATEGORY COLOR BIN COUNTRY OF ORIGIN 5 ...
Page 5
... TYP. (0.020 ± 0.005) NOTES: 1. DIMENSIONS ARE IN mm (INCHES). 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE ON DIMENSIONS IS ± 0.38 mm (0.015 INCH). 3. LEAD MATERIAL: SOLDER PLATED COPPER ALLOY. Figure 4. HCMS-397X Package dimensions. 5 5.36 (0.211) TYP 11.43 (0.450) MAX. DATE CODE (YEAR, WEEK) INTENSITY CATEGORY ...
Page 6
... Logic Supply Voltage V LOGIC [1] LED Supply Voltage V LED [1] GND to GND – LED LOGIC Note: 1. For further description, see Appendix B, Electrical Considerations, “V Considerations”. 6 Orange HCMS-3904 HCMS-3914 HCMS-3964 HCMS-3974 .......................... -0 7.0 V LOGIC .................................... -0 5.5 V LOGIC [1] ..................... - + [ Min. Max. Units 3.1 5 ...
Page 7
... Refers to the initial case temperature of the device immediately prior to measurement. 2. For comparison purpose with existing HCMS-29xx 5 V devices. The Typical and Minimum Luminous Intensity per LED Character Average can be calculated by dividing the values in the table by two for the test condition 50% Peak Current, 100% Pulse Width and V 3 ...
Page 8
Electrical Description Pin Function Description RESET (RST) Sets Control Register bits to logic low. The Dot Register contents are unaffected by the Reset pin. (logic low = reset; logic high = normal operation). DATA Serial Data input ...
Page 9
AC Timing Characteristics over Temperature Range (-40 to +85 C) Timing Diagram Ref. Number Description 1 Register Select Setup Time to Chip Enable 2 Register Select Hold Time to Chip Enable 3 Rising Clock Edge to Falling Chip Enable Edge ...
Page 10
... Display Overview The HCMS-39XX series is a family of LED displays driven by on-board CMOS ICs. The LEDs are configured as 5x7 font characters and are driven in groups of 4 characters per IC. Each IC consists of a 160-bit shift register (the Dot Register), two 7-bit Control Words, and refresh circuitry ...
Page 11
... CONTROL REGISTERS NOTE: 1. DATA IS COPIED TO THE CONTROL REGISTER OR THE DOT LATCH AND LED OUTPUTS WHEN CE IS HIGH AND CLK IS LOW. Figure 5. HCMS-39XX write cycle timing diagram. Pixel Map In a 4-character display, the 160- bits are arranged as 20 columns by 8 rows. This array can be ...
Page 12
... REGISTER D Q SELECT RS (LATCHED) REFRESH CONTROL RESET RST PRESCALE VALUE H ÷8 OSC OSCILLATOR L H OSC SELECT BLANK Figure 6. Block diagram for HCMS-39xx. 12 DATA OUT RS (LATCHED SER/PAR MODE DI 40 BIT S.R. DATA DO DO OUT CURRENT REFERENCE ANODE PWM BRIGHTNESS CONTROL 0 ...
Page 13
PIXEL DATA TO NEXT CHARACTER Figure 7. Pixel map. Control Register The Control Register allows software modification of the IC’s operation and consists of two independent 7-bit control words. Bit D in the shift register selects 7 one of the ...
Page 14
Control Register Data Loading Data is loaded into the Control Register, MSB first, according to the procedure shown in Table 1 and Figure 5. First brought to logic high and then CE is brought to logic low. Next, ...
Page 15
Table 2. Control Shift Register. CONTROL WORD Bit D 7 Set Low to Select Control Word 0 Peak Current Brightness Control – DISABLES ...
Page 16
... These bits must always be programmed to logic low. Cascaded ICs Figure 8 shows how two ICs are connected within an HCMS-39XX display. The first IC controls the four left-most characters and the second IC controls the four right- most characters. The Dot 1 Registers are connected in series to form a 320-bit dot shift register ...
Page 17
RESET CLK RESET CLK D D OUT OUT SEL SEL OSC OSC D IN Figure 8. Cascaded ICs. 17 IC1 BITS 0-159 CHARACTERS 0 RESET IC2 BITS 160-319 CLK ...
Page 18
Appendix A. Thermal Considerations The display IC has a maximum junction temperature of 150 C. The IC junction temperature can be calculated with Equation 1 in Table 3. A typical value for R is 100 This value ...
Page 19
Appendix B. Electrical Considerations Current Calculations The peak and average display current requirements have a significant impact on power supply selection. The maximum peak current is calculated with Equation 3 in Table 3. Table 3. Equations. Equation 1: T MAX ...
Page 20
... The inputs to the ICs are protected against static discharge and input current latch up. However, for best results, standard CMOS handling precautions should be used. Before use, the HCMS-39XX should be stored in antistatic tubes or in conductive material. During assembly, a grounded conductive work area should be used and assembly personnel should wear conductive wrist straps ...
Page 21
Appendix D. Refresh Circuitry This display driver consists of 20 one-of-eight column decoders and 20 constant current sources, 1 one-of-eight row decoder and eight row sinks, a pulse width modulation control block, a peak current control block, and the circuit ...
Page 22
For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 ...