AT29LV020-10JCSL383 Atmel, AT29LV020-10JCSL383 Datasheet
AT29LV020-10JCSL383
Related parts for AT29LV020-10JCSL383
AT29LV020-10JCSL383 Summary of contents
Page 1
... Five-volt-only commands determine the opera- tion of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29LV020 is performed on a sector basis; 256 bytes of data are loaded into the device and then simultaneously programmed. ...
Page 2
... Pin Configurations Pin Name A0 - A17 I/O0 - I/O7 NC 2.1 32-lead PLCC Top View 2.2 32-lead TSOP (Type 1) Top View AT29LV020 2 Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect A14 A13 A11 ...
Page 3
... Read The AT29LV020 is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high. This dual-line con- trol gives designers flexibility in preventing bus contention ...
Page 4
... DATA Polling The AT29LV020 features DATA polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin ...
Page 5
... These two 8K memory sections are referred to as boot blocks. Secure code which will bring up a system can be contained in a boot block. The AT29LV020 blocks are located in the first 8K bytes of memory and the last 8K bytes of memory. The boot block programming lockout feature can therefore support systems that boot from the lower addresses of memory or the higher addresses ...
Page 6
... MHz mA 3.6V OUT 1 -100 µ 3. AT29LV020-20 AT29LV020-25 0°C - 70°C -40°C - 85°C 3.3V ± Manufacturer Code ( Device Code Manufacturer Code IL ...
Page 7
... ACC after the falling edge of CE without impact AT29LV020 AT29LV020-20 AT29LV020-25 Max Min Max Min 120 200 120 200 50 0 100 ACC ...
Page 8
... Input Test Waveforms and Measurement Level t R 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. These parameters are characterized and not 100% tested. AT29LV020 < Max 6 12 Units Conditions OUT 0565D– ...
Page 9
... CE Controlled Notes: 1. The software data protection commands must be applied prior to byte loads complete sector (256 bytes) should be loaded using these waveforms as shown in the Software Protected Byte Load waveforms (see next page). 0565D–FLASH–2/05 (1)(2) AT29LV020 Min Max Units 10 100 0 0 200 ...
Page 10
... ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA TO ENTER DATA (3) SECTOR (256 BYTES) PROTECT STATE AT29LV020 10 (1) Notes: 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Data Protect state will be re-activated at end of program cycle. 3. 256 bytes of data MUST BE loaded. (2) Min ...
Page 11
... Toggle Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 0565D–FLASH–2/05 (1) (1) (1)(3) AT29LV020 Min Typ Max Min Typ ...
Page 12
... Manufacturer Code is read for Device Code is read for The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code is 1F. The Device Code is BA. AT29LV020 12 25. Boot Block Lockout Feature Enable Algorithm (2)(3)(5) ADDRESS 00000H Notes: 1. Data Format: I/O7 - I/O0 (Hex) ...
Page 13
... AT29LV020-12JC 32J AT29LV020-12TC 32T AT29LV020-12JI 32J AT29LV020-12TI 32T AT29LV020-20JC 32J AT29LV020-20TC 32T AT29LV020-20JI 32J AT29LV020-20TI 32T AT29LV020-25JC 32J AT29LV020-25TC 32T AT29LV020-25JI 32J AT29LV020-25TI 32T Ordering Code Package AT29LV020-10JU 32J AT29LV020-10TU 32T Package Type AT29LV020 Operation Range Commercial (0° to 70°C) Industrial (-40° ...
Page 14
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT29LV020 14 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 15
... Orchard Parkway San Jose, CA 95131 R 0565D–FLASH–2/05 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT29LV020 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – ...
Page 16
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...